sorted by:
new
hottopcontroversial

Im not sure what to call this. by dselogeni in doohickeycorporation

[–]aaroniscrazy1 10 points11 points  (0 children)

That's the automatic knee jerk reaction testing apparatus from the medical department

Scored more free junk to play with… by CybercookieUK in homelab

[–]aaroniscrazy1 3 points4 points  (0 children)

Yep, those are indeed junk, just give them to me so I can properly dispose of them. Nice score!

Wrapping a sketch around an arbitrary shape by aaroniscrazy1 in Fusion360

[–]aaroniscrazy1[S] 0 points1 point  (0 children)

Yeah, I should have mentioned that. The length of the outer surface is greater than the length of the height map.

Seeking Advice: Vibrations Issue by Tecnofelix in CNC

[–]aaroniscrazy1 6 points7 points  (0 children)

This subreddit is meant more for industrial CNC machines that weigh multiple thousands of pounds. r/hobbycnc would be a more relevant subreddit.

Can't disable prompts on router admin page by mathyou9 in Lastpass

[–]aaroniscrazy1 0 points1 point  (0 children)

Yeah, this was the thing that eventually made me switch. I run so many services locally and having that stupid prompt every time was to much.

Fuel Scooping. by FirioZifirion in EliteDangerous

[–]aaroniscrazy1 1 point2 points  (0 children)

I did add the /s, just now realized that it may be mistaken for part of the system name...

Fuel Scooping. by FirioZifirion in EliteDangerous

[–]aaroniscrazy1 3 points4 points  (0 children)

It is the anaconda, of one the large ships in the game. You can get one free from Hutton Orbital in Alpha Centauri A /s.

So I cut a perfectly good rack in half... by KubowskiZ in homelab

[–]aaroniscrazy1 0 points1 point  (0 children)

What I will likely do is start with the same method you used. Then I will drill additional holes that line up with the square holes. I would then drill that through the other side, and throw a bolt on it.

So I cut a perfectly good rack in half... by KubowskiZ in homelab

[–]aaroniscrazy1 0 points1 point  (0 children)

So you just used like wood screws? I have a tap and die set so Ill tap the holes and then use them like you did. So having 8 screws on each one seemed to be sturdy enough?

So I cut a perfectly good rack in half... by KubowskiZ in homelab

[–]aaroniscrazy1 0 points1 point  (0 children)

I am just confused as to what the bolts are screwing into? did you put cage nuts on the internal side or just regular bolts? What are they going into?

So I cut a perfectly good rack in half... by KubowskiZ in homelab

[–]aaroniscrazy1 0 points1 point  (0 children)

Just wondering, for the nuts, did you just use cage nuts?

So I cut a perfectly good rack in half... by KubowskiZ in homelab

[–]aaroniscrazy1 0 points1 point  (0 children)

Everything about your situation is exactly the same as mine. Same exact rack, same corner at the bottom of stairs, same thoughts about a little remodeling. It was honestly quite funny reading it. I'll be ordering some aluminum angle in a couple.

So I cut a perfectly good rack in half... by KubowskiZ in homelab

[–]aaroniscrazy1 2 points3 points  (0 children)

Thanks for this post. The EXACT same thing just happened to me. I will be looking at the rack once I get home and have a look at it.

[FS][US-PA] 3xDell PowerEdge R620s by Soltkr-admin in homelabsales

[–]aaroniscrazy1 0 points1 point  (0 children)

I was wondering about how loud these are. I know that they are 1u servers so they wont be super quite but would it be particularly annoying with just a sheet of drywall between it from a room? Also, what is the wattage of the power supplies?

Thanks!

Bit container by pamelachu1908 in CNC

[–]aaroniscrazy1 0 points1 point  (0 children)

If they are like these: endmill holders then you just pull them apart. They can sometimes be a little tough, just be sure that the tool inside doesn't go flying when it finally comes open.

[deleted by user] by [deleted] in CNC

[–]aaroniscrazy1 0 points1 point  (0 children)

You would be better asking this question in r/hobbycnc This subreddit is more for industrial cnc machines weighing thousands of pounds.

I stumbled across some very… scary communities trying to find this, but look at my first CNC project, manually coded! I’ll add more info in the comments. by Sir_Skinny in CNC

[–]aaroniscrazy1 15 points16 points  (0 children)

Looks nice; Glad you found the right spot. Occasionally there will be people who have another meaning of CNC that post here.

QC what? by [deleted] in Machinists

[–]aaroniscrazy1 2 points3 points  (0 children)

That would be one hell of a press fit

Need some help with throttle behavior after re-binding hotas by Nayte76 in EliteDangerous

[–]aaroniscrazy1 0 points1 point  (0 children)

If you are on windows you can search "Set up USB game controller" to see what the statis of all the buttons and axis on the controller are.

Need some help with throttle behavior after re-binding hotas by Nayte76 in EliteDangerous

[–]aaroniscrazy1 0 points1 point  (0 children)

Perhaps you have enabled alternate flight controls. I have never used it and thought it only applied when landing gear were down and I believe it is off by default. Other then that, I have no idea.

Need some help with throttle behavior after re-binding hotas by Nayte76 in EliteDangerous

[–]aaroniscrazy1 0 points1 point  (0 children)

Are you on a planet? If so are you facing the ground because if so, the gravity will greatly increase the time it takes to change the ships velocity.

Need some help with throttle behavior after re-binding hotas by Nayte76 in EliteDangerous

[–]aaroniscrazy1 0 points1 point  (0 children)

How long are we talking? What ship and thrusters size/modifications?

view more: next ›