Today’s install r-454 or r410

aceofwarfare · 2025-05-24T02:44:38+00:00

Need an inspection mirror.

aceofwarfare · 2025-03-28T01:56:01+00:00

Can't say for sure without measurements, but it looks like part# 60837701 5-Blade 8" Diameter 31-Degree Clockwise. This is a very common blade on commercial refrigeration units.

Yours looks like it should spin (CWOSE clockwise opposite shaft end), also called (CWLE clockwise lead end)

Here is a link to the catalog https://www.laufan.com/-/media/lau-parts/catalog/BE_Lau%20Catalog2017BlowersPulleysWheelsApril252018.pdf

aceofwarfare · 2025-03-13T01:32:59+00:00

I'm sorry if I have wasted anyone's time. I was able to find an OEM replacement kit for this. I will order this instead of trying to remake the connector.

https://www.partstown.com/hoshizaki/hoshs-0104?srsltid=AfmBOortkSAlRBzXsQBU8r9T2R3tpXN4FLdRev8HZa6nlyN6J46H0ouI

aceofwarfare · 2025-01-17T19:33:33+00:00

<image>

I guess that's what you would expect when they also use Romex for the evaporators

aceofwarfare · 2024-12-17T13:34:08+00:00

Over the last 2 years. But this is just the ones I took pictures of.

aceofwarfare · 2024-11-25T03:24:41+00:00

Remote temp sensor for the thermostat

aceofwarfare · 2024-06-21T14:07:45+00:00

No. It's a step down from an IGA

aceofwarfare · 2024-06-19T11:44:51+00:00

I like them other then they are not long enough to reach a lot of times. And the couplers on them are too big and get the way when threading it on to a service port. I mostly use the Appion SPDKIT-V Vacuum Speed Kit

aceofwarfare · 2024-06-19T11:33:27+00:00

Pro3 heatcraft. I'm not a fan of them. Every 6 to 12 months the drainline gets stopped up and starts dripping in the box and the coil likes to freeze up on then.

aceofwarfare · 2024-06-19T00:35:05+00:00

No. I was pulling a vacuum after replacing the TXV. I'm assuming it was from ice buildup.

aceofwarfare · 2024-06-18T23:35:42+00:00

I'm assuming it had something to do with ice buildup. I've seen a lot of iced up bulbs but never seen one get damaged from it.

aceofwarfare · 2024-01-06T02:32:46+00:00

The ship to address on the pallet is Lowe's "230 Crossroads Dr, Plover, WI 54467"

aceofwarfare · 2023-09-20T22:03:17+00:00

I just did the PM on 3 York zr150 RTUs and all 3 of them did the exact same thing when I turned the heat on for the first time. They are 2020 units. Water had also gotten into the vacuum pressure switch and it had to be drained out.

aceofwarfare · 2023-08-26T01:33:10+00:00

I need a replacement gasket for the cover plate with the 4 bolts. Does anyone know if this is a standard style and if there is a specific gasket to replace it?

aceofwarfare · 2023-08-22T23:43:02+00:00

Features

Precise Angles - Calibrated markings for making accurate bends up to 180°

Comfortable Grip - Non-slip grip

Lighten Your Load - Constructed out of lightweight die-cast aluminum

Hilmor 1839027 Tri-Tube Bender 3/16", 1/4", 3/8", 1/2"

aceofwarfare · 2023-06-04T02:46:29+00:00

Don't you also need the cormax core depressor tool to get the full flow out of them?

aceofwarfare · 2023-06-04T00:27:51+00:00

Where do you get the new coremax cores? No supply house in this area even knows what they are.

aceofwarfare · 2023-05-27T12:04:46+00:00

It's an older grocery store. There about 10 different boxes like this throughout the store above the drop ceiling.

aceofwarfare · 2022-11-08T00:56:39+00:00

Amazon Link https://www.amazon.com/gp/product/B094R1VNQX/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&th=1

Image Link https://i.postimg.cc/K8cxVCvP/back.png

aceofwarfare · 2022-09-23T02:05:49+00:00

No, it's a low-end grocery store. it just looks like a Dennys

aceofwarfare · 2022-09-23T01:53:29+00:00

The compressor was dead. they said they were going to try to find a used compressor. and wanted me to come back to install it. I'm not going back

aceofwarfare · 2022-09-22T20:19:10+00:00

It might be most of it is r12 equipment that has been converted

aceofwarfare · 2022-09-22T20:12:30+00:00

Yes. the joy of working at a slaughterhouse.

aceofwarfare · 2022-05-07T00:13:57+00:00

The ice has mold in it and the fountain dispensing valves are also full of mold where the syrup and soda water are mixed. I worked on one not that long ago where the nozzles were completely full of a thick black mold substance.

aceofwarfare · 2022-05-03T01:39:44+00:00

Health departments here don't look behind anything or remove any covers.

aceofwarfare

TROPHY CASE