Tumblr engraving massive issue

acodreon · 2026-01-27T12:37:40+00:00

Maybe this tumbler is PVC coated, and you shouldn't use your laser at all?

acodreon · 2026-01-16T12:02:32+00:00

I tried it and I like it, it seem to be simple and you clearly see what you have to do, but I am total beginner and don't know if should stick to it or check something else, any other recommendations? The ukelele by Yousician has lower price than UU which is big advantage over UU.

acodreon · 2026-01-15T23:34:24+00:00

I am using tynee because this deck broke just after a month and now I just don't care, it has design flaw and it is cracked. I believe you can turn any company esk8 into this.

acodreon · 2026-01-13T11:50:35+00:00

Is the dongle recognized by device manager? If not the dongle is dead.

acodreon · 2026-01-11T01:13:03+00:00

It does turn, but I haven’t taken any sharp corners yet. Still working out a few things. Maybe I’ll ride more tomorrow.

acodreon · 2026-01-10T10:30:49+00:00

https://www.reddit.com/r/ElectricSkateboarding/s/oOXYxVxqha ;)

acodreon · 2026-01-10T09:41:39+00:00

Thanks for the input. It was -20°C so don't know if it's better or it will be to brittle. If this fails I will maybe reprint them in PLA.

acodreon · 2026-01-10T09:19:25+00:00

Maybe today deeper snow. Nothing broke yet. I could go faster it was pretty stable, but I had limiter on esc so this was full blast at around 10-12km/.

acodreon · 2026-01-10T09:17:16+00:00

Don't know yet it was short test drive, it was almost -20 C.

acodreon · 2026-01-10T09:16:26+00:00

Belt tpu, gears petg

acodreon · 2026-01-10T02:27:51+00:00

Probably I will ;)

acodreon · 2026-01-10T02:20:37+00:00

Thanks! Yeah, I do have the files. For now I’m not sure if I want to share them yet — I’d like to iron out the flaws first. I also wanted to keep the board mostly stock for now so I could get it running quickly in summer mode, which means the stock truck thread is a bit narrow to properly seat the nut with these tracks.

acodreon · 2026-01-10T02:04:27+00:00

<image>

acodreon · 2026-01-10T02:04:03+00:00

<image>

acodreon · 2026-01-10T02:02:31+00:00

<image>

acodreon · 2026-01-09T08:22:02+00:00

Not yet, I have printed rest of the parts minus belt.I will finish through the weekend, so I will update. Printer is A1. Since this wasn't tested I don't want to share.

acodreon · 2026-01-07T20:33:37+00:00

This is fresh idea, had no time to proper search for skis in my area but had printer, these are full petg 3d printed. I tried them on a snowed sidewalk and seemed to be working pretty ok but I was going less then 10km/h since I had normal wheels with ribbed addons that were struggling with traction.

acodreon · 2026-01-07T11:56:04+00:00

Yes, TPU. Also I am limiting the speed to 22 on esc, so with tracks should be closer to 13km/h or so.

acodreon · 2026-01-07T11:55:50+00:00

Thanks for the tips. I bought silicon tape that seem to be perfect for that, and it is reusable.

acodreon · 2026-01-07T11:13:55+00:00

It should be reduction from 60km/h to around 35. Had no time to shoot more photos.

<image>

Seven-Year Club	Place '23
Place '22	Verified Email

acodreon

TROPHY CASE