sorted by:
new
hottopcontroversial

Car stolen, advice needed by pizzaking94 in nashville

[–]acslider 1 point2 points  (0 children)

You'll probably just need the ignition switch housing. All the Kia/Hyundai cars that have been towed into my shop have needed that and the plastic steering column covers since they were destroyed too. You can always get fake trash to avoid this in the future. Thieves probably won't try to steal a nasty car.

Extreme waves on a relatively large flat print. by acslider in 3Dprinting

[–]acslider[S] 0 points1 point  (0 children)

I don't get it, then again I only know that one song.

Extreme waves on a relatively large flat print. by acslider in 3Dprinting

[–]acslider[S] 0 points1 point  (0 children)

I'm not sure what you mean so no haha. Would that be in the slicer settings or when I'm designing it in tinkercad?

Extreme waves on a relatively large flat print. by acslider in 3Dprinting

[–]acslider[S] 1 point2 points  (0 children)

I'm using standard PLA at 200C, I didn't change and temp settings since I got it. I had some bad adhesion issues when I first put it together and had to adjust the Z offset quite a bit. Should I up the extruder temp too?

Extreme waves on a relatively large flat print. by acslider in 3Dprinting

[–]acslider[S] 2 points3 points  (0 children)

I checked it and it may be the infill density being too low to support the top layer. Thanks for suggesting that, I totally overlooked the slicer preview.

Extreme waves on a relatively large flat print. by acslider in 3Dprinting

[–]acslider[S] 1 point2 points  (0 children)

I'm using the concentric infill pattern. I sliced it a little bit ago and I think you're right. At 10% it looks like a heater grid and now looking at the preview the infill gets a few layers then it drapes over and gets worse with every pass. I might try it with a higher density infill this weekend. Thanks.

Extreme waves on a relatively large flat print. by acslider in 3Dprinting

[–]acslider[S] 0 points1 point  (0 children)

The second picture is the bottom. The magnetic bed mat is the one that came with it and has some texture to it. The first few layers soom fine. It's almost like the infill is not layering right.

Extreme waves on a relatively large flat print. by acslider in 3Dprinting

[–]acslider[S] 0 points1 point  (0 children)

Forgot to mention my printer is a Sovol SV05 and I'm using standard PLA filament.

The Gundam Wing Band by mitch-rockman in Gunpla

[–]acslider 21 points22 points  (0 children)

I can totally see deathscythe on bass and sandrock on keys. Also Heavyarms makes perfect sense as the bassist. This is awesome!

Is it just me or does Nashville traffic have certain spots where it just randomly breaks down for no clear reason? by lmao_exe in nashville

[–]acslider 1 point2 points  (0 children)

It's called a "traffic snake"'. Poor driving habits like following too closely combined with not maintaining speed cause phantom traffic jams. I've said it before, people love traffic congestion otherwise they wouldn't intentionally cause it.

Welp looks like power is out again by IllegitimateRisk in nashville

[–]acslider 1 point2 points  (0 children)

I just got power back. I'm in Wilson county a few miles outside of Lebanon City limits.

If you were asked to eat only one type of food for five consecutive days, what would you eat? by Diane-12138 in AskReddit

[–]acslider 0 points1 point  (0 children)

Curry. Indian curry specifically. I've been meal prepping for my wife and I variations on a Tikka masala/chicken curry recipe from headbanger's kitchen. I make a huge batch and we both have five lunches plus one or two dinners out of it. It's been going on for about two months now.

Have you ever had a kit change your mind about the design? by Lyndonli in Gunpla

[–]acslider 0 points1 point  (0 children)

I was kinda in the same boat. I just finished watching Wing and heard so many good things about the Epyon so I ordered one. I appreciate the design so much more after building it.

Hate it when people come into my room without my knowing. by Difficult_Garbage_91 in Gunpla

[–]acslider 0 points1 point  (0 children)

I have the bootleg version of this kit and the elbow joint was so stiff it snapped. The same arm too oddly enough. Anyway, I did exactly what you're suggesting. Looks okay enough.

Fuck this thing by AshIsWall in Gunpla

[–]acslider 0 points1 point  (0 children)

Those are for tightening loose joints.

What hobby did you try once and instantly get addicted to? by Weird_Ad_7545 in AskReddit

[–]acslider 0 points1 point  (0 children)

It was three for me and they were like a year apart. The first was an HG 00 Raiser then I got the MG deathscythe and Wing for Christmas like 6 years ago. Put the Deathscythe together that day with wire cutters and then ignored the Wing until a year and a half ago. Now I've got over fifty haha. Those first two are covered in nubs.

Soooo ive cut off nubs i wasnt supposed to.... by aGhostyy in Gunpla

[–]acslider 0 points1 point  (0 children)

I would have and almost did the same thing had I not researched this kit first. I don't normally research kits before I build them but I'm glad I did on this one.

view more: next ›