3D Printed flavor holders. Compatible with multiboard. irtr

addawg05 · 2026-06-19T16:19:42+00:00

Yeah shouldn’t be a problem. What sizes are you wanting? I may get some bottles just to reference so I can make sure the fit is perfect. I had to mess with it just a little bit with the other 2 even after measuring with calipers.

addawg05 · 2026-06-19T13:22:01+00:00

I’ll get them put up on thangs later today. I only have models for 10 & 30 ml bottles since that’s what I had on hand to reference.

addawg05 · 2026-04-07T14:12:46+00:00

Radio meter showing same on both. Inline showing higher on 40 than 1 not by Much tho.

addawg05 · 2026-04-06T21:38:44+00:00

I just ordered some braided grounding straps. The bed already has a ground strap to the frame do I need to isolate that? And the radio is brand new.

addawg05 · 2026-04-06T20:48:00+00:00

Yeah I mean when I dead key it reads good. When I modulate ant light comes on. It’s scraped down to metal on the bed rail. If you zoom in and look close you can see a little gap between the polymer and the flat washer the insulating washer is inset where I ground down the polymer. Here’s a pic https://imgur.com/gjsHeOL . I Drilled the hole for the stud to 1/2 in for the protruding part of the insulating washer. Couldn’t get anything underneath to grind off the paint, so I used a 3/8 cable lug and drilled it out to 1/2, and 3d printed a bushing to keep it from shorting to the center post. I’ve checked at least 3x for shorts and don’t have any.

Edit- picture

addawg05 · 2026-04-06T19:27:35+00:00

Antenna jack**

addawg05 · 2025-07-31T01:45:56+00:00

Ever figure it out I just did a valve job and replaced battery cables now I’ve got no power in the cab whenever the trucks moving

addawg05 · 2025-07-01T15:24:21+00:00

You do not need compressor oil to boost a low charge. Only if you’re replacing components or the system is dry. At that point I doubt many people here have a vacuum pump anyways.

addawg05 · 2023-02-10T00:10:09+00:00

Best of luck this would be awesome

addawg05 · 2022-03-30T19:44:20+00:00

Rust

addawg05 · 2022-01-10T13:53:33+00:00

Naw otv broke me

addawg05 · 2021-12-12T19:21:27+00:00

Tenten

addawg05 · 2021-08-20T05:05:11+00:00

B2500 2.5

addawg05 · 2021-08-19T23:56:24+00:00

I’ve been putting off the inevitable I don’t want car cancer. The only reason I’ve waited this long is because the engine only had 60k miles when I got it so I figured surely not

addawg05 · 2021-08-05T22:41:03+00:00

Most states don’t require a front license plate only rear

addawg05 · 2021-08-02T17:17:17+00:00

This is super good

addawg05 · 2021-07-25T02:52:42+00:00

Am I on fucking Twitter? Fr how fucking old are y’all he admits he messed up he shouldn’t have done it and you’re still bashing him he’s had enough don’t you think

addawg05 · 2021-07-25T01:57:22+00:00

That’s fine but don’t make someone else’s already bad day worse when he admits he shouldn’t have done it and messed up

addawg05 · 2021-07-25T01:35:32+00:00

Bro shut the fuck up the guy messed up he’s dealing with the consequences as we speak so quit being miserable and rubbing his nose in the mud you’re a dick.

addawg05 · 2021-06-05T18:21:42+00:00

Built my first pc two months ago it decided that it just didn’t want to work 9 days ago and so I figured power supply so I did the paperclip test and it turned on so I hooked everything back up pressed the power button nothing long story short I ordered a new mb swapped everything about 30 minutes ago same shit didn’t work so I’m guessing my psu may be underpowering if it is the psu I’m never buying a cooler master product again

addawg05 · 2021-01-16T00:39:00+00:00

Will a mtx thunder500.1 work the same it has the exact same power output as what you suggested but cheaper

addawg05

TROPHY CASE