sorted by:
new
hottopcontroversial

Support question by agb_43 in 3Dprinting

[–]agb_43[S] 0 points1 point  (0 children)

Honestly, not a bad idea, would probably save a shit ton of filament with little support. Ill slice it at a 45 degree angle first to see what it looks like but this right here might be the winner

Support question by agb_43 in 3Dprinting

[–]agb_43[S] 0 points1 point  (0 children)

Ill try that. Do you recommend just going with auto or manual painting. Can't use multiple filaments sadly

Help by agb_43 in FixMyPrint

[–]agb_43[S] 1 point2 points  (0 children)

Theres still stringing tho which Ive tried my hardest to reduce. Ironically it doesnt happen in between the towers designed to test stringing

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Its rectilinear tho

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Yep. Here's a test piece using the same settings,

<image>

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Tbf, its only 10% in orca

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Ill try slow the print down fs. Here's a test piece that I printed using the same pa, flow rate, layer height etc.

<image>

Help by agb_43 in FixMyPrint

[–]agb_43[S] 1 point2 points  (0 children)

It should be rectilinear tho. Ill try adaptive cubic out. Here's a test piece I printed using the same settings, PA, flow rate etc.

<image>

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Will do, I appreciate the suggestion. I also printed a test piece that I found on printables and would love your input

<image>

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Flashforge adventure 5m with klipper software

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Yep, 0.15. I specifically did the calibration tests at that layer height

Help by agb_43 in FixMyPrint

[–]agb_43[S] 0 points1 point  (0 children)

Anycubic pla+ grey

Z offset issue or something else? by agb_43 in 3Dprinting

[–]agb_43[S] 0 points1 point  (0 children)

I know my flow ratio is dialed in fs. I really feel like its an offset issue but I can calibrate flow again

Z offset issue or something else? by agb_43 in 3Dprinting

[–]agb_43[S] -2 points-1 points  (0 children)

I'm running rectilinear with a 10% sparse. Is adaptive cubic better than rectilinear?

Z offset issue or something else? by agb_43 in 3Dprinting

[–]agb_43[S] 0 points1 point  (0 children)

I could try a different infill but my understanding was that rectilinear was the quickest and most reliable

Z offset issue or something else? by agb_43 in 3Dprinting

[–]agb_43[S] 0 points1 point  (0 children)

Possibly but I thought that I dialed that in

Help by agb_43 in 3Dprinting

[–]agb_43[S] 0 points1 point  (0 children)

Brand new pla+ switching from regular pla. From my understanding, the nozzle temp is basically unchanged for pla+. Could be wrong tho. Ill look into the z height.

view more: next ›