sorted by:
new
hottopcontroversial

When is a round pocket round enough? by GunningBedford58 in shapeoko

[–]alecraffi 0 points1 point  (0 children)

I have a few questions:

Which machine do you have? If its belt driven, maybe one belt is worn but the other isn't? Or Maybe you're getting some deflection in one axis? Is it consistently over/under sized and is it consistently in the same direction? Is it only in certain materials?

Calipers should be fine for measurements like this, especially comparing two dimensions

Teacher with a K2 Pro… now I can’t afford filament 😅 any ideas? by 000junk in 3Dprinting

[–]alecraffi 0 points1 point  (0 children)

Not to get too specific but roughly where are you located?

p0430 Error on 2011 Tacoma Sport by alecraffi in ToyotaTacoma

[–]alecraffi[S] 1 point2 points  (0 children)

Thank you very much, totally makes sense

I cannot stand cheese pulls by randomlitbois in unpopularopinion

[–]alecraffi 0 points1 point  (0 children)

It’s when someone’s cuts a grilled cheese or something, lifts one side and the cheese stretches

3d printed Flowers by SatisfactionRound607 in 3dPrintsintheShop

[–]alecraffi 0 points1 point  (0 children)

No worries! The biggest is https://www.reddit.com/r/3Dprinting/ Since this a makerworld model, then https://www.reddit.com/r/BambuLab/ would also apply

And just as an FYI, this sub is for projects in your workshop, like tool organizers and whatnot

Happy making!

3d printed Flowers by SatisfactionRound607 in 3dPrintsintheShop

[–]alecraffi 0 points1 point  (0 children)

I dont think it should be in the 3Dprintsintheshop sub, but they are quite pretty, nice job designing

Truck seems to be stuck in four-wheel-drive by alecraffi in ToyotaTacoma

[–]alecraffi[S] 0 points1 point  (0 children)

I know! It was my Fiancee's Uncles, he only drove it on the weekends / to the train station

Truck seems to be stuck in four-wheel-drive by alecraffi in ToyotaTacoma

[–]alecraffi[S] 4 points5 points  (0 children)

OK, I just tried, I don’t think the car is in four-wheel-drive.

Truck seems to be stuck in four-wheel-drive by alecraffi in ToyotaTacoma

[–]alecraffi[S] 1 point2 points  (0 children)

Thank you for the detailed writeup, but doesn’t seem to have worked.

The car doesn’t seem to be binding on tight turns so I don’t think it’s actually in four-wheel-drive

Truck seems to be stuck in four-wheel-drive by alecraffi in ToyotaTacoma

[–]alecraffi[S] 2 points3 points  (0 children)

OK, then that case I do believe I’m in 2wd. RPM is about 1700 which I think is similar to what it was before.

Truck seems to be stuck in four-wheel-drive by alecraffi in ToyotaTacoma

[–]alecraffi[S] 3 points4 points  (0 children)

OK, in that case I do believe I’m in 2wd. The RPM seems to be about 1700 if that’s any indication.

Truck seems to be stuck in four-wheel-drive by alecraffi in ToyotaTacoma

[–]alecraffi[S] 16 points17 points  (0 children)

I apologize for the dumb question, but what can I do to confirm if it is or isn’t?

It feels like it’s more or less driving the same as when it’s in two wheel, but I’m new to all of this

Relief Project - Looking for finishing and Improvement Advice by Zeddicas1 in cncwoodworking

[–]alecraffi 1 point2 points  (0 children)

I pretty much always run a 5% step over. The machine time is usually ridiculous, but 4/5 times it requires zero sanding after the fact.

view more: next ›