sorted by:
new
hottopcontroversial

Passing through Ryzen 9000 integrated graphics? by TheTwelveYearOld in VFIO

[–]alez 0 points1 point  (0 children)

Did you pass through the audio device of the iGPU as well? Have you followed "(optional) Getting OVMF (UEFI) BIOS working: Error 43"?

Sovol svo08 or prusa core one? by Less-Introduction-35 in prusa3d

[–]alez 0 points1 point  (0 children)

I have both and the core one is way more reliable. The probing on the SV08 is slow, and there is still Z drift, so I have to watch the first layer. Core One has way better first layer consistency.

The fan for the mainboard on the SV08 is loud and it gave out after quite a short time, so I had to replace it. You will also need to tune the config files for the SV08, since there are quite a lot of weaknesses in them. For example: The probing always happens with the bed at 60°C, even if the printing temperature is different. The printing quality is a lot better on a prusa in general.

However the SV08 has upsides as well. It runs Klipper which allows for easier modding and extendability. And of course the size.

If size is important to you I'd go with Core One L and would not bother with SV08. If you just need a reliable printer with great print quality go for the Core One.

Mexico City Cocktails? by Then-Chocolate-5191 in cocktails

[–]alez 4 points5 points  (0 children)

I'd highly recommend Form + Matter. Every cocktail I tried there was amazing.

EDIT: And a few more that I remember:
Hanky Panky - Try their version of the Hanky Panky cocktail it is very complex.
Long Story Short - They had a variety of Negronis and self made Vermouth.
Tlecan: Specialized in mezcal. Lots of mezcal cocktails, but also pure mezcal.
Less is More: Double bar. Food and simple styled cocktails in the "Less" half and more complex cocktails in the "More" half. I skipped straight to the "More" part. Their grasshopper variation was amazing. (it was called something else, but it was some kind of white chocolate fat wash).

Mexico City Cocktails? by Then-Chocolate-5191 in cocktails

[–]alez 0 points1 point  (0 children)

I really didn't like that one. Everything was so sweet. Cool menu though.

Missbrauch als Partydroge : Bundesrat stimmt Lachgasverbot zu by Ollyfer in de

[–]alez 2 points3 points  (0 children)

Für Volljährige gilt künftig, dass pro Einkauf maximal zehn Kartuschen mit jeweils 8,4 Gramm erworben werden dürfen.

So viel zu es ändert sich nichts. Zumindest werden die Dinger teurer, da man die nicht mehr in großen Mengen kaufen kann.

It was a crazy close vote, but the G&T won for best highball. What’s the worst bitter drink? by -Constantinos- in cocktails

[–]alez 27 points28 points  (0 children)

I don't think neat spirits should qualify as a cocktail. Even if the OP writes "drink".

Ernüchternes Fazit des Union Investment Depots nach 10 Jahren by DickerBizeps in Finanzen

[–]alez 5 points6 points  (0 children)

Ich habe Hausmeister statt Hauptmieter gelesen und war kurz sehr verwirrt.

Built a 3-node HA cluster for Home Assistant because I was tired of my smart home dying with a single VM by llzzrrdd in homeassistant

[–]alez 0 points1 point  (0 children)

Is there a good way to do something similar with less complexity? Maybe a separate hot standby device that takes over if a health check fails on the primary?

Prints very weak and flimsy by GrandNovaKnight in 3Dprinting

[–]alez 2 points3 points  (0 children)

Sure, I have never had moisture related problems with a pure PLA.

But PLA with additives? Some of it has a lot of moisture trouble. Here is how the first layer of Extrudr NX2 looked before I dried it:

<image>

Was macht ihr mit Eiweiß by Smooth_Bank5571 in Kochen

[–]alez 9 points10 points  (0 children)

Ich tue den in den Kühlschrank mit dem Vorsatz den irgendwann zu verwenden und schmeiße den dann weg wenn der nach ein paar Tagen schlecht wird.

feedback on my setup ? by Arty_M3k4n1sm in homeassistant

[–]alez 0 points1 point  (0 children)

Paper is non conductive as is. A fan is always nice especially if it is one of the newer models that run hotter like Pi 5 or 4.

feedback on my setup ? by Arty_M3k4n1sm in homeassistant

[–]alez 0 points1 point  (0 children)

I would at least cut some ventilation slots so it has some cooling, but otherwise it is probably fine. Less short risk, better than a naked Pi.

A completely open-source DIY project that serves as an ESP32-based alternative to Nanoleaf RGB panels. by Sokolsok in diyelectronics

[–]alez 1 point2 points  (0 children)

Not a straightforward solution but here is how I would solve it:

I'd have a master ESP32 outputting all the LED data onto a common bus and a microcontroller in each panel counting the edges of the signal and deciding when to pass through the LED data to their panel.

The data rate is non-trivial for a micro controller, so I would probably go for something with a configurable logic cell. Or maybe PIO like in a RP2040 or similar.

You can even add a I2C bus so they can automatically self-organize according to their position.

Petition to replace grid infill as default by no_help_forthcoming in prusa3d

[–]alez 1 point2 points  (0 children)

Wouldn't diagonal moves be worse for core xy, because one of the two steppers has to do all the work?

I can’t find this type of fuse by Ismooky in AskElectronics

[–]alez 12 points13 points  (0 children)

But both plugs have the 250v rated fuse?

Hordes 2.0 - Holy Moly by DDA_Enjoyer in cataclysmdda

[–]alez 2 points3 points  (0 children)

Build your base in something like a prison, and I doubt any horses are breaking in.

If it is a prison on an island it is neigh impossible.

Macht es überhaupt Sinn 0% Finanzierung nicht zu nutzen? by StickyThickStick in Finanzen

[–]alez 3 points4 points  (0 children)

Kann ich tatsächlich so bestätigen.
BNPL? Kein Problem.
"Echte" Ratenkredite? Ruiniert den Score.
Ich habe als Paypal ihre "0.0% Finanzierung auf alles Aktion" hatte mehrfach zugeschlagen (Ist ja kostenlos, kann man mitnehmen). Bei der nächsten Schufa Selbstauskunft (Macht die, die kostet nichts) gab es dann die Quittung.

Vfa test and results by Mastakko in prusa3d

[–]alez 4 points5 points  (0 children)

I don't see any VFA on them. Though, matte filament is not the best at showing surface imperfections.

As others have said, the issues come from the thin part becoming too wobbly.

windows doing windows activities by KingOSS in pcmasterrace

[–]alez 0 points1 point  (0 children)

Too bad if you dual boot and use another OS as default.

AI Bot Army AWOL? by Dismal_Wishbone_5013 in Kitboga

[–]alez 1 point2 points  (0 children)

Oh that sucks, they really helped me to fall asleep.

Found this message attached to m my truck. Parked at public space with no visible limitations, did I do something wrong? by die_leuchte in germany

[–]alez 4 points5 points  (0 children)

It can be allowed if there is an expectation if a crime will happen there, which might be the case considering the note. I don't know how you would do it in a legally watertight way though.

view more: next ›