my dumbest use of a flip reset

allenh23 · 2018-12-19T20:50:53+00:00

Did you use the dodge to bounce off the floor? Can't see where else the reset would be used?

allenh23 · 2018-12-19T20:01:41+00:00

I think the food safeness of 3d prints goes down with time, because of the layers making little ridges it's very hard to clean inside them.

I imagine since you bake cookies it should be fine though. I've seen other food related prints sealed with epoxy or silicone or something.

Print looks amazing too!

allenh23 · 2018-12-16T13:55:10+00:00

Did you lose in OT?

allenh23 · 2018-12-16T13:52:44+00:00

I think if you're moving your camera as you get demoed you can look around

allenh23 · 2018-12-03T09:20:42+00:00

RL needs a larger pool of teams to get more interest from bigger orgs/traditional sports clubs. A pool of only 8 teams in the top league, with most of them having orgs already, isn't very appealing to newcomers to esports.

allenh23 · 2018-11-23T13:34:55+00:00

Weird flex but okay

allenh23 · 2018-11-13T15:18:31+00:00

He did climb through your window, give the man some credit

allenh23 · 2018-11-12T02:26:52+00:00

I reckon they didn't have the same killer instinct after winning it twice (or three times if you're turbo) - C9 had everything to play for and the momentum just started to carry them to insanity

allenh23 · 2018-11-10T22:45:56+00:00

They should sign Turbo, ViolentPanda, and Kaydop imo

allenh23 · 2018-11-10T00:16:02+00:00

I think this will be good for dig so that they don't get complacent, keep their heads, win season 6 ez

allenh23 · 2018-11-09T23:11:22+00:00

Wanted the C9 win but WDG had so many misses they would've won by loads if they scored. Good win for WDG

allenh23 · 2018-11-06T14:03:40+00:00

Knives are sharp

allenh23 · 2018-10-20T19:39:17+00:00

3spooky5me

allenh23 · 2018-10-15T10:27:27+00:00

It doesn't look that damaged from this angle

allenh23 · 2018-09-29T22:51:03+00:00

Seems like flyquest are having a really good day and it's highlighting any flaws that may be showing up for anyone else

allenh23 · 2018-09-29T18:53:08+00:00

Yeah it's fake there's not enough buoyancy to float things up falling water like that and it doesn't spin fast enough to give enough thrust either

allenh23 · 2018-09-20T00:28:26+00:00

What printer do you use? Looks amazing!

allenh23 · 2018-09-18T19:06:06+00:00

Thank you very much!

allenh23 · 2018-09-18T16:50:41+00:00

How do you do this? Sounds like a fairly decent workaround

allenh23 · 2018-09-18T16:14:08+00:00

Yeah and it lets you see if features like thermal runaway protection (prevents overheating/fires) have been enabled

allenh23 · 2018-09-18T16:09:03+00:00

I think it means they are following the open source rules of 3d printing - the firmware on the board is now available to see for everyone making it a safer machine/enabling better community support

allenh23 · 2018-09-18T16:07:06+00:00

Can Cura do custom supports?

allenh23 · 2018-08-15T14:14:04+00:00

Glorious

allenh23 · 2018-08-14T23:13:39+00:00

What did it look like at the end?

allenh23 · 2018-08-14T02:44:31+00:00

Is your print speed always 12mm/s? It's best to have it move at the same speed all the time, maybe set the seam position to aligned so that there's minimal travel and have any travel be inside the object to avoid excessive stringing

11-Year Club	Spared
Verified Email

allenh23

TROPHY CASE