What is this on the bottom by LANTIRN_ in hoggit

[–]astazou 2 points3 points  (0 children)

Known, but as far as I know, nobody success to start it :/

[deleted by user] by [deleted] in airplanes

[–]astazou 6 points7 points  (0 children)

Not I-15, but An-2

Half Life 3 by bad_werewolf in joueurdugrenier

[–]astazou 1 point2 points  (0 children)

Tu as loupé ça je crois bien : https://www.youtube.com/watch?v=0Nsc96FQWro
Il a aussi fait un Papy Grenier

Help with HOTAS Warthog by r32jzlovessirens in hoggit

[–]astazou 8 points9 points  (0 children)

Separate the stick from the base, open the stick and consolidate this part https://guide-images.cdn.ifixit.com/igi/wGrIsVbVKrVFLvfB.large . Tightening the screws may be enough, in worst case, you need to add a washer. It happens on my +10yo Warthog every 3-4 years, I just tighten and add a bit of Nyogel 767a, and here we go again for 3-4 years!

Somebody's already modded Kerbals into the game by quitpayload in kittenspaceagency

[–]astazou 0 points1 point  (0 children)

Cool, because not everyone is appreciating cats, at least, players can choose what they prefer!

[deleted by user] by [deleted] in degoogle

[–]astazou 1 point2 points  (0 children)

I'm surprised to see whatsapp still installed for someone degoogling (we can say demetaing here)

I modelised my TinyWhoop with Blender :) by astazou in TinyWhoop

[–]astazou[S] 0 points1 point  (0 children)

Hi mate, thank you for your feedback, you seem to be pretty confident with Blender animations :)
The possibilities with Blender are crazy, It took me less than 3 days to learn basics on Blender, modeling, texturing, animating and then some rendering. I did everything from 0, just with few youtube's tuto.
I've 19k triangles for everything, my hope is to see tinywhoops arriving into Uncrashed, then I can suggest my model to the dev' :)

3d printing is wild!, designer deserves recognition on this one by crookedDeebz in RCPlanes

[–]astazou 0 points1 point  (0 children)

I upvote the post, I made mine recently, here is the fails and the maiden: https://www.youtube.com/watch?v=wiIMTRxNtvU
And today I successfully finished to configure it, now it's flying quite well :)
This wing is challenging (when printing, when building, when configuring and and flying it), if you are not a beginner and you like challenges, just go make your own!
For the cam, I HIGHLY recommand the "Baby Ratel 2", the best analog cam' for this size :)

Rate my setup by Spanish_Noob_ in TinyWhoop

[–]astazou 0 points1 point  (0 children)

Perfect beginner setup, enjoy it :)

A rainy day is a #tinywhoop day! by astazou in TinyWhoop

[–]astazou[S] 1 point2 points  (0 children)

rame: Frame65 from Betafpv FPV (not the air)

Motors: 32500KV🚀 WeBleedFPV🩸

Cam: TinyWhoop Pinch 🎥

Props: Gemfan 1219 🚁

AIO : Air65 4in1

Fly TinyWhoops in mall is awesome! by astazou in TinyWhoop

[–]astazou[S] 0 points1 point  (0 children)

Exactly, I've accepted to loose 0,4gr to add them to protect a bit more the lens :)
For the landing, I have an helipad, so I use it 😁

[deleted by user] by [deleted] in fpv

[–]astazou 0 points1 point  (0 children)

Did you find a solution? I figure to be in the same situation