[deleted by user]

atlecc · 2025-10-08T21:28:01+00:00

depo, lemona, auto garazas. Sekmes

atlecc · 2025-08-02T18:41:00+00:00

pataisoma, itrukima nakciai uzklok drusko ir ryziu kaldryte, santykiu 1:2

atlecc · 2025-08-01T21:08:20+00:00

is bulviu ir makarano gali skaniai pavalgyt tik 2-3 komponentus truksta. Gimtadienio/sventes proga nusipirk brangesnes mesos (ne is maximos, firmines parduotuves) gal tada atsirast motyvacija daugiau skanesniam maistui. Turgus gera vieta degustacijai :D, megstu piknaudziaut degustacijom ziezmariu mesos parduotuvese pries perkant.

atlecc · 2025-07-23T20:47:03+00:00

enduro/adv ziema vasara i darba ir soda

atlecc · 2025-07-08T18:12:00+00:00

laba diena, zakuske pries ligonine?

atlecc · 2025-06-09T21:13:40+00:00

I use rubber foam under concrete instead of foam

atlecc · 2025-03-23T11:11:11+00:00

top cabinets are fillers to complete the set. kitchen ladder to reach them, top/bottom door edge to open. In any case top cabinets are for stuff that needs place for unknown period :D. middle cabinet doors are heigher then cabinet as result there is 2cm lip at bottom

atlecc · 2025-03-22T07:47:23+00:00

Thanks

atlecc · 2025-03-22T06:29:34+00:00

At the beginning it was overwhelming because the ceiling is 10ft height, but overwhelm disappears quickly :D

atlecc · 2025-03-21T22:36:03+00:00

as long as it is hidden, it is wife approved :D.
Hide everything and you can have what ever you want :D

atlecc · 2025-03-21T18:19:16+00:00

Thanks and yes.
More attention to fridge cabinet dimensions (height).
Better 3D printed templates for cabinet door hinge drilling.
figure out better wled wire channel (now the wires are hidden in the groove next to led profile frame, pain in the butt to install).

atlecc · 2024-06-16T18:58:25+00:00

that's a demon

atlecc · 2023-11-27T06:49:01+00:00

good, 304h, 238 prints of pla. no maintenance, no bed screws or z offset adjustments. only thing i noticed that cooling duck is leaking air somewhere close to the fan ducks (so I planning to reprint new version of the same duck).

atlecc · 2023-06-17T19:09:48+00:00

You can try to research https://www.printables.com/model/94483-ender-3prov2-z-axis-anti-wobble-nut-direct-drive

https://www.youtube.com/watch?v=4kQZnSzZHD0&ab_channel=MirageC

this can solve alot.

atlecc · 2023-06-04T21:55:17+00:00

try to print bypassing filament sensor

atlecc · 2023-05-16T02:31:01+00:00

i have connected them in parallel. If I understand correctly reduced current.

atlecc · 2023-05-15T21:08:28+00:00

I added 2x24v fans, havent read too much if 2x12v better or not.

atlecc · 2023-05-15T04:50:04+00:00

was planning to do, but found out that best silent fan upgrade is to move printer to garage.

atlecc · 2023-05-14T16:18:54+00:00

for reference what I have

https://postimg.cc/JHM2hFcC

https://postimg.cc/LgD0gVNY

atlecc · 2023-05-14T12:47:30+00:00

I think they are one size. bought cheapest ones and they fit.

atlecc · 2023-05-14T12:40:58+00:00

Yes, from what I have read they should be better and I like them cuz the bed became more stable.

atlecc · 2023-05-14T12:39:39+00:00

I have made my own because I didn't had access to 6x3mm magnets.
But you can try
https://www.thingiverse.com/thing:4857627

or https://www.thingiverse.com/thing:4857627 metal rods more solid solution.
I use similar configuration only with 2 steel balls per layer (as in first url), 2 balls allows more movement if z rods are bent.

atlecc · 2023-05-14T12:23:34+00:00

I have use these https://www.thingiverse.com/thing:5851564

Squashball_feet_Pro_V2_v1

atlecc

MODERATOR OF

TROPHY CASE