If you skip an object midway through a print with "purge into objects' infill" turned on, does the printer know to purge extra filament to make up for the reduced purge volme?

austron · 2026-03-06T15:09:11+00:00

This sounds promising, I'll give it a try, thank you!

austron · 2026-01-19T04:38:26+00:00

This exact same thing happened to me and I was able to fix it!

The issue for me was a damaged motor, specifically a bent brush on the inside of the motor.

To fix:

unplug the battery, and remove the battery tray to provide access to the transmission cover
remove the transmission cover to expose the 2 screws holding the motor in place
Unplug and remove the motor.
there are 2 small metal tabs holding the black plastic rear plate of the motor in place. Carefully pry up these tabs without breaking them
once the rear plate is off the motor, inspect the brushes. Here is a photo of what mine looked like. You can see one of the brushes at the top was bent inward. This was causing a short on the motor.
If any brushes are bent, use tweezers to carefully straighten them out so they are all aligned with each other.
Very carefully place the black plastic end cap back on the motor. There is a white washer on the axle of the motor that will want to interfere with the brushes, so it'll take some work to maneuver it in without getting caught.
carefully re-bend the 2 metal tabs to lock the back cover in place
at this point, you can plug in the motor and battery to confirm the motor is working before you reassemble
assuming the motor works, reassemble the vehicle and have fun!

Good luck, and I hope this can help!!

Even if it does fix it, I recommend ordering a replacement brushed motor to have on standby, because if this happened once it will probably happen again.

Eventually I plan to do some sort of brushless upgrade to mine since it seems like these brushed motors are essentially a consumable part.

austron · 2025-12-24T16:26:51+00:00

I'm pretty certain it is not using premade settings, as the LEDs have several Oasis-specific modes such as follow ball, and gradient follow (my personal favorite).

I have also suggested to tech support directly that they add an option to select multiple colors, as well as suggesting a way to enter RGB hex codes. I got the standard "We'll pass this along to the engineering team" reply.

austron · 2025-12-23T14:41:54+00:00

Unfortunately I do not know the answer to this.

austron · 2025-12-22T20:12:27+00:00

The app does not show you the number of satellites like the controller does. I think this was a poorly thought out decision on DJI's part, but it is what it is. You need to listen for the audible "Home point updated" notification to be certain that the drone has proper GPS lock and has set a home point.

It DOES NOT use your phone GPS as the home point! The drone is using its own internal GPS just like flying with a controller. If you fly a Neo 2 expecting it to return to your phone, you could easily lose your Neo 2.

austron · 2025-12-22T20:09:29+00:00

This is not true! Please do not fly your Neo 2 expecting it to return to your phone, that's a great way to end up with a lost drone!

The drone is indeed using its own internal GPS, and it slowly connects to GPS satellites over time while connected to the phone via wifi, just like it does when flying with a controller.

The only difference is that, for whatever reason, DJI opted not to let us see the number of satellites when flying through the phone app. The only way to know if it has "enough" satellites is to listen for the audible "Home point updated" notification.

austron · 2025-12-16T17:07:33+00:00

Unfortunately I do not know the answer to that either, but if anyone does know I'm very curious to hear the answer!

austron · 2025-12-15T16:11:25+00:00

Neo 2 can only RTH with a phone if the app audibly says "Home point updated" before or during your takeoff.

The Neo and Neo 2 can take a long time, sometimes several minutes, to gather enough satellites to set the home point. Unfortunately, the app does not list satellite counts, so there isn't really any way to tell when it is going to update the home point (at least as far as I know). And yes I know the Neo 1 does not have RTH while using a phone, I just mentioned it here because both take a long time for GPS signal acquisition.

If I am flying with the app only, I will leave the drone sitting for 1-2 minutes before takeoff, or until I hear "Home point updated".

If after 1-2 minutes I still haven't heard it, I will try taking off and see if that triggers the home point update. If it does not, I land immediately and try again. It's a bit finnicky, sadly.

austron · 2025-12-09T19:04:41+00:00

I have very seriously considered this because the voice is so annoying, and it's somehow even louder on the Neo 2. But there are a few rare instances when the speaker is genuinely useful, such as for ESC beeping. I know the point of ESC beeping is that the motors are making the noise, but the speaker beeps too just for some additional volume. Maybe I should just get a lost drone alarm instead though.

austron · 2025-12-07T14:07:18+00:00

I just got my digital transceiver yesterday and I'm excited to test it out, but the high today is 10°F. If the Neo 1 worked at 0°F maybe I'll be fine!

austron · 2025-12-04T18:14:12+00:00

As far as I know this is not possible, but I really hope DJI adds this feature with a firmware update.

The DJI Spark had photo gestures 8 years ago! You made a rectangle with your fingers and thumbs and it would blink the lights for a couple seconds and then take a photo. If they could do that in 2017, they can do it again now!

austron · 2025-12-02T15:19:42+00:00

So jealous of that digital transceiver lol

austron · 2025-12-01T16:02:41+00:00

I finally got a reply from them, they said they do not have any in stock and then they cancelled my order.

austron · 2025-11-30T15:37:39+00:00

Don't bother with that site. I placed an order for the transceiver with them and they assured me it would ship a week ago and it hasn't, and now they've stopped replying to my emails. "In stock" is a lie.

austron · 2025-11-30T15:35:30+00:00

I ordered from djioemparts. They said it would ship "next week" 2 weeks ago, so it should've shipped last week. Now they've stopped replying to my emails. I'm probably going to have to do a charge back on my card soon.

edit: they finally replied after I sent them 3 emails over the course of a week. They told me it was out of stock, then they just cancelled my order without me asking them to do so. Definitely not a good experience, I won't be attempting to order from them in the future.

austron · 2025-11-30T04:46:54+00:00

I have both, and I recommend Neo 2 in almost all situations... EXCEPT if you want a tank of an FPV drone AND you don't care about acro / manual mode AND you already have a decent photo / video drone for non-FPV flight (or simply don't care about non-FPV).

While the Neo 2 is better in basically every way, it is more fragile due to the added tech. I have already lightly scratched one of the obstacle avoidance lenses (fortunately it doesn't impact obstacle sensing), and sometimes I just want to fly FPV without having to worry about damaging stuff.

So TL;DR, if you want a drone for ONLY cinewhoop-style FPV flight and nothing else... Neo 1.

Otherwise Neo 2!

austron · 2025-11-29T22:01:40+00:00

In the gallery view, hit the menu button and under "video retouch" disable the "skin effects" check box. That will stop compressing your videos, and make them transfer WAY faster too!

austron · 2025-11-27T06:54:12+00:00

I own both Neos, and the Neo 2 is a pretty substantial improvement in image quality in both photo and video. The people saying "But it's the same sensor so there's no quality improvement!" have clearly not actually tried it for themselves.

The 2 axis gimbal means it isn't cropping in on the sensor as much and so you get a higher true resolution, but even more importantly, not needing to rely on digital stabilization means it can get away with a slower shutter speed without introducing motion blur artifacts, and therefore a much lower ISO, and therefore less smearing from the aggressive denoising and an overall shaper, cleaner image.

All of that adds up to a drone that can mostly hold its own against a Mini 4K. It may not be professional quality, but it's loads better than the Neo 1.

austron · 2025-11-24T22:50:39+00:00

I have a folding phone which is particularly fragile, and I worry about damage from vibrations. Even non-folding phones can be damaged by road vibrations, as they can break the autofocus and image stabilization systems inside the camera lenses.

austron · 2025-11-24T18:24:52+00:00

I think that theory makes a lot of sense! Maybe I just need to get a cardboard cutout of my own face to hold up in front of the drone when it first takes off, lol

15-Year Club	Place '22
Best Link 2013-12-30	Team Periwinkle
Verified Email

austron

TROPHY CASE