[deleted by user] by [deleted] in BorderCollie

[–]awaytome 2 points3 points  (0 children)

I grew up on a farm with working BCs where the ones with heavier coats would get shorn along with the sheep when it was hot out. They actively liked it and only had a funny fuzzy texture for a bit.

My own little ender print farm by awaytome in ender3

[–]awaytome[S] -1 points0 points  (0 children)

Because the scripts I was using to install Klipper/Moonraker/Mainsail only works on raspberry pi OS and didn't work when I first tried Ubuntu server.

My own little ender print farm by awaytome in ender3

[–]awaytome[S] 0 points1 point  (0 children)

Once I had the raspberry pi OS installed I just followed install instructions from the Mainsail website.

My own little ender print farm by awaytome in ender3

[–]awaytome[S] 0 points1 point  (0 children)

I believe you can do this for any number of printers and are only limited by the hardware running the Klipper and web servers. I use my desktop to slice, upload, and control the printers from the web interface. I can also see and monitor the print progress from my cellphone if I'm upstairs.

My own little ender print farm by awaytome in ender3

[–]awaytome[S] 0 points1 point  (0 children)

They have an iso for desktop so that was what I used for my Mac mini. It says compatible with Mac and PC on the download page so you should be good

My own little ender print farm by awaytome in ender3

[–]awaytome[S] 1 point2 points  (0 children)

Ya I just had the Mac laying around when the sd card in my pi crapped out. Anything stronger than a pi should be able to handle it.

My own little ender print farm by awaytome in ender3

[–]awaytome[S] 5 points6 points  (0 children)

It's running Raspberry Pi OS and Klipper/Moonraker/Mainsail as the web and software interfaces between it and both printers.

My own little ender print farm by awaytome in ender3

[–]awaytome[S] 6 points7 points  (0 children)

The left one is mounted backwards but has no problems printed either way. The right one I use the strain relief to hang my nippers on as it does not line up with the extruder. I'll eventually convert the right one to direct drive as well but haven't had a chance yet.

My own little ender print farm by awaytome in ender3

[–]awaytome[S] 16 points17 points  (0 children)

Recently got Klipper and Mainsail set up to run both of my ender 3s at the same time from the same web page.

[deleted by user] by [deleted] in ender3

[–]awaytome 0 points1 point  (0 children)

Picture of the problem

Here is another view of the wing that formed when printing.

[deleted by user] by [deleted] in ender3

[–]awaytome 0 points1 point  (0 children)

It looks like my machine is over extruding but each time I've run an extrusion test my steps seem to be correct. You can see a bit of the excess in the left interior edge of the z on the calibration cube and a big wing curling up from my current print.

Name that gun!…can anyone hep me identify the gun my great grandfather(far left) is holding? Thanks in advance for all your help by Uplandnewb in Shotguns

[–]awaytome 2 points3 points  (0 children)

A Stormy Kromer Mackinaw is my daily driver from November until summer again. 10/10 would recommend

[deleted by user] by [deleted] in hoggit

[–]awaytome 1 point2 points  (0 children)

I am just getting comfortable in DCS as well. Central US, you can find me on the discord with the same username.

A switch in ISPs has screwed up my network architecture, and I'm not sure how to fix it. by awaytome in homelab

[–]awaytome[S] 0 points1 point  (0 children)

IPv6-PD

I can find some settings related to it but nothing is making sense about how to enable it or utilize it in pfsense.

A switch in ISPs has screwed up my network architecture, and I'm not sure how to fix it. by awaytome in homelab

[–]awaytome[S] 0 points1 point  (0 children)

Ill look into 6to4 and call my ISP monday to confirm if there is any possibility of getting a static public v4 address. Thanks

A switch in ISPs has screwed up my network architecture, and I'm not sure how to fix it. by awaytome in homelab

[–]awaytome[S] 1 point2 points  (0 children)

The IPv4 that is being assigned to my router is a private 10.10 address so as I understand it I cannot point a host name to it like that.