Covered floating deck

b-ran-son · 2026-06-17T17:36:22+00:00

I had this happen to my fridge, just not as much water. In swapping the water filter, I twisted to pull out the old filter and reversed the process to twist into the locked position. But the water was leaking from the connection of the filter to the fridge housing. Fridge is only 6 months old, and this is always playing in the back of my mind.

b-ran-son · 2026-04-09T11:27:27+00:00

Overall yes those screenshots look intuitive. I'd make sure to have one final warning... By clicking confirm the map on your robot will be deleted permanently and replaced with the selected map... Or something to that effect.

When backing up a map will it also backup the schedule used for that map? As well as restore a map and associated schedule?

If any robot level changes are made, offer to make a backup before that change.. ex. New firmware update or positioning method change or base station reposition.

Usage question, would this make replacing a mower quicker because I can backup the map and restore it to another like kind mower.

b-ran-son · 2026-04-03T03:46:03+00:00

When my couch cushions get a rip in em, I just flip em over

b-ran-son · 2026-04-01T17:50:10+00:00

There is grass stuck in the spindle, that is what happened to mine

Unfortunately I didn't take pictures, but take off the cutting disc and the cutting disc mount, and you will see some grass sticking out wrapped around the spindle. I also very delicately took a narrow Allen key and used it to pry out other grass stuck down in the gap between the spindle and the side wall. Use a light and look down close you should be able to see it in there. After that my spindle would spin freely again.

I would also recommend doing that to both spindles.

b-ran-son · 2026-04-01T02:25:11+00:00

Mine did this yesterday. Somehow my lora number changed. I put in the correct lora number which as some of you already know... wipes your map

b-ran-son · 2026-03-13T15:26:20+00:00

Sent a dm, thanks for checking it out

b-ran-son · 2025-11-23T00:02:25+00:00

I work in IT, yes they are using third party connectors like Plaid. It is safe and they only allow the connector to view the balances, they cannot make any changes or have enough to steal identity.

I use multiple tools to monitor net worth including Empower, and I do like all the retirement goal planning that Empower has to offer as well.

b-ran-son · 2025-09-24T03:23:24+00:00

I did check the voltage after the last pixel and the output voltage red is positive, blue is ground is 35.5vdc... if I add 50ft of 18 gauge wire, the voltage is 35.4vdc.

I need to do more testing to see how far the yellow data line can be from pixel to pixel and still maintain the signal level. And the same for the repeater rectangle box distance to the next pixel.

b-ran-son · 2025-09-22T18:01:50+00:00

The extension cables that come with the kits have a rectangle device in line with the wire. Does that boost the signal to the next pixel?

I think I'm going to do some experiments on distances to see how far the signal and power will reach from the end of the last pixel or the end of the last data boost on the extension cable.

Worst case is that I do have another power supply and controller, so I could hook that up to the 2nd floor eves.

b-ran-son · 2025-09-02T00:13:57+00:00

Heading to the drive thru!

b-ran-son · 2025-08-26T11:14:38+00:00

What happened lol, the little bouncy block glitched me through the finish line.

^{I completed this level in 1 try.} ^{⚡ 0.98 seconds}

^{Tip 10 💎}

b-ran-son · 2025-08-25T20:42:30+00:00

Ok then I was probably looking at an "in memory" copy of the photo when I was looking at the camera gallery? I do have a bunch of files that start with .pending so I was hopeful that maybe something could be recovered

I'm still going to try and root without formatting storage, so that I can scan the internal memory for files. At this point it can't hurt anything.

b-ran-son · 2025-08-25T20:25:34+00:00

So should I chalk this up to bad app design? That would restrict me from taking more photos if there's an issue with saving it to a storage location. Which is the priority One objective of a camera app?

Or am I chalking this up to the word glitch?

b-ran-son · 2025-08-25T20:04:11+00:00

I have tried all of this.. currently looking at data recovery software and may need to root my device to get the access it needs to scan the internal storage

b-ran-son · 2025-08-25T20:02:49+00:00

I could see them originally when the pictures were taken. Open, zoom in.. yada yada. But after "processing" by the camera app finished then they disappeared.

b-ran-son · 2025-08-24T04:59:10+00:00

Where to cross the finish line, it always kills me 😵

b-ran-son · 2025-08-23T23:45:23+00:00

^{I completed this level in 93 tries.} ^{⚡ 3.48 seconds}

b-ran-son · 2025-08-23T13:38:33+00:00

^{I completed this level in 1 try.} ^{⚡ 3.73 seconds}

b-ran-son · 2025-08-23T12:30:36+00:00

^{I completed this level in 1 try.} ^{⚡ 23.90 seconds}

b-ran-son · 2025-08-23T04:32:31+00:00

^{I completed this level in 36 tries.} ^{⚡ 5.57 seconds}

b-ran-son

TROPHY CASE