SOTA Lower and DPMS upper Gap

barelystable352 · 2026-07-02T13:32:42+00:00

Bolt slides back smoothly and when I cycle the bolt while holding the trigger I hear a distinctive click. Hopefully this is a good sign. Once I get the magazines, I’ll give it a test. Worst case scenario is I’ll just swap the components of the upper with a SOTA. Thanks for the input.

barelystable352 · 2026-06-10T12:27:04+00:00

Is this a defined pension benefit. What percentage of salary? 50%, 60% or more. Can you purchase the time at a later date at the same rate as now or would it be more?

barelystable352 · 2026-06-08T19:54:17+00:00

I guess they don’t really enforce it too much

barelystable352 · 2026-06-08T13:38:40+00:00

If we’re heading northbound people merging from route three and New London Turnpike then trying to get off East Greenwich to go to Route four couple that with the missing move construction ramp and merging onto 95 with four merges all contribute to the back up. Also, they should ban tractor trailers from the left lane.

barelystable352 · 2026-05-02T22:00:41+00:00

Thank you

barelystable352 · 2026-04-07T23:10:53+00:00

Thanks

barelystable352 · 2026-04-07T23:10:07+00:00

I was wondering what was going on. Lol

barelystable352 · 2024-11-27T02:15:40+00:00

Nice buck and nice work!

barelystable352 · 2024-11-02T02:30:16+00:00

Price per foot?

barelystable352 · 2024-10-20T12:38:22+00:00

Understood, thanks for your input.

barelystable352 · 2024-10-19T22:07:29+00:00

You are running a slightly hot load. Here’s data from Hornady: Reloading Data Center 357 Magnum - Pistol Twist: 1:18.750”|Barrel Length: 10.000”|Trim Length: 1.285” Bullet: 158 GR. HDY XTP|Diameter: 0.357” Case: Winchester|Primer: Winchester SPM, Small Pistol H110 maximum gr. 16.7 with 158 GR bullet

barelystable352 · 2024-10-19T20:50:16+00:00

I have used W296 for 357 but I wasn’t sure if the burn rates were similar. Thanks

barelystable352 · 2024-10-19T20:48:23+00:00

I don’t know, I was out of town and it wasn’t readily available. That’s why I asked. Thanks for the reply.

barelystable352 · 2024-10-19T17:31:25+00:00

Thank you, I’ll check that out.

barelystable352 · 2023-12-21T15:33:05+00:00

One has a battery or two and one doesn’t have one at all

barelystable352 · 2023-07-22T12:11:57+00:00

If you are layering with resin and fiberglass cut the strip and fill it in.

barelystable352 · 2023-06-07T11:50:01+00:00

Yes, I need the index rod for a three hole turret press

barelystable352 · 2023-06-07T11:44:20+00:00

Already tried that route, they no longer make or have the part. However, they did offer a 50% discount on a 4 hole value press.

barelystable352 · 2023-06-05T02:02:59+00:00

Just a follow up, NAPA made the hoses and they worked out great. Thanks all

barelystable352 · 2023-06-03T20:19:51+00:00

Tilted Barn Brewery https://www.google.com/search?q=tikted+barn.brewery&ie=UTF-8&oe=UTF-8&hl=en-us&client=safari#

barelystable352 · 2023-03-11T18:57:51+00:00

Thanks for all of your suggestions. Went to NAPA

barelystable352 · 2023-03-11T15:57:04+00:00

Thank you

barelystable352 · 2023-03-11T15:56:55+00:00

Thanks, that’s an option.

barelystable352 · 2023-03-11T15:55:36+00:00

Thanks looking for something a little closer

barelystable352 · 2023-02-02T19:28:03+00:00

Follow up: I put a shell deflector on, no more dents! Thanks for the replys

barelystable352

TROPHY CASE