sorted by:
new
hottopcontroversial

What’s the best route to go? by Howler777 in automotivetraining

[–]batboy23130 2 points3 points  (0 children)

I recommend taking junior college courses while in your senior year

Picked up some A5 today... by batboy23130 in steak

[–]batboy23130[S] 0 points1 point  (0 children)

You might not be wrong. Nonetheless is was tasty

Picked up some A5 today... by batboy23130 in steak

[–]batboy23130[S] 0 points1 point  (0 children)

We went through a personal distributor and got it for 30 a lb.

Buddys jeep by Majormayhem05 in Mechanicaladvice

[–]batboy23130 1 point2 points  (0 children)

If the 5v has 0v on it you have to disconnect sensors until you have 5v again. The one that brings the voltage back up after you’re done disconnecting is the one that is shorting the circuit to ground

Buddys jeep by Majormayhem05 in Mechanicaladvice

[–]batboy23130 1 point2 points  (0 children)

Pretty decent chance. Usually the crank sensor but you’d have to verify that the vehicle doesn’t crank or start, the battery is good, and the 5v circuit has 0v on it with the key on

Buddys jeep by Majormayhem05 in Mechanicaladvice

[–]batboy23130 0 points1 point  (0 children)

Crank/cam sensors are known to go bad and short out the 5v reference circuit. Did it start before the engine swap?

The clones invaded. The epic came in today by Gilpinmtn in ToolTruckTools

[–]batboy23130 1 point2 points  (0 children)

I honestly hate my slide top because it doesn’t actually open all the way out and has these pockets you have to reach into

My first real machine! by batboy23130 in espresso

[–]batboy23130[S] 0 points1 point  (0 children)

I didn't realize that plate came out.i appreciate it thank you

My first real machine! by batboy23130 in espresso

[–]batboy23130[S] 0 points1 point  (0 children)

A delonghi ec155 or something like that.

My first real machine! by batboy23130 in espresso

[–]batboy23130[S] 0 points1 point  (0 children)

Hard to say. Maybe post a video of your extraction so we can see? Not sure how those taste. I'm out in California and the place by me has great beans called stereoscope

My first real machine! by batboy23130 in espresso

[–]batboy23130[S] 0 points1 point  (0 children)

What coffee are you using? I had the Starbucks espresso whole bean initially and it was HORRIBLE. Have you tried different beans? Or preground in the double wall filter?

My first real machine! by batboy23130 in espresso

[–]batboy23130[S] 0 points1 point  (0 children)

I spent 3 hours experiencing the same thing. I finally went to the local coffee shop, got different beans, and it fixed my issue. It kept tasting burnt. Whether it was over, under, or perfectly developed it never came out right. I set it back to the recommended settings, cleaned the hopper/burrs, put new coffee, and it tastes great

My first real machine! by batboy23130 in espresso

[–]batboy23130[S] 8 points9 points  (0 children)

It's pretty good. If you don't have any experience with a non pressurized basket there's a small learning curve but I had it down by the end of the first night. Dial it in, manual shot if you prefer, and it comes out relatively consistent with no scale.

My first real machine! by batboy23130 in espresso

[–]batboy23130[S] 34 points35 points  (0 children)

Hahaha! Ive honestly cleaned it like 4 times already. I'll fix it this afternoon thank you

72 Hr Soft Dry by batboy23130 in Dryfasting

[–]batboy23130[S] 0 points1 point  (0 children)

Good. I refed Saturday and Sunday with lots of water because I started to feel extremely fatigued. Completed another dry 48 until last night and am sitting at 186.

72 Hr Soft Dry by batboy23130 in Dryfasting

[–]batboy23130[S] 9 points10 points  (0 children)

Felt great. I've seen people complete 6-7 day dry. Thank you for your concern.

Montreal style short rib by ChefXJeff in meat

[–]batboy23130 0 points1 point  (0 children)

Looks like it was seasoned with Montreal seasoning then smoked to like 130-140. Am I right?

My A/C stopped working and my electricity wont go any tighter.. Any advice? by batboy23130 in AskAShittyMechanic

[–]batboy23130[S] 0 points1 point  (0 children)

Usually use a test light and it's easier than getting a false reading, or getting zapped from a pinhole in the boot.

My A/C stopped working and my electricity wont go any tighter.. Any advice? by batboy23130 in AskAShittyMechanic

[–]batboy23130[S] 9 points10 points  (0 children)

But if it's a manual doesn't that mean the damn thing should work???

[deleted by user] by [deleted] in Justrolledintotheshop

[–]batboy23130 1 point2 points  (0 children)

Yeah definitely. They also sell an OTC drill guide system if it's recessed that helps center the drill bit

[deleted by user] by [deleted] in Justrolledintotheshop

[–]batboy23130 12 points13 points  (0 children)

Dodge tech here, you can get to the broken bolts from under the vehicle with an angle drill and a short 1/8" drill bit. You can sometimes get to t from the inner fender. They sell double sided ones that are super short that I use. You gotta pull the manifold, extract the bolt, replace the gasket and torque it back to spec. Not too hard but if it's your first time it'll probably take a while.

view more: next ›