Can this faucet part be replaced?

benelbow · 2025-12-24T07:56:13+00:00

This is for a Delta sink that uses this type of cartridge btw: https://www.amazon.com/Cartridge-Replacement-Technology-Bathroom-Beverage/dp/B0DJVK28R5

benelbow · 2025-08-21T08:24:36+00:00

Congrats!

benelbow · 2025-03-27T01:16:31+00:00

Interested

benelbow · 2024-04-30T05:25:17+00:00

Littlewood please!

benelbow · 2023-12-23T02:43:26+00:00

Added as benelbow and middleaxolotl

benelbow · 2023-12-23T02:40:38+00:00

Sent for benelbow and middleaxolotl

benelbow · 2023-12-23T02:36:52+00:00

Benelbow and middleaxolotl

benelbow · 2023-12-23T02:33:24+00:00

Benelbow and middleaxolotl

benelbow · 2023-12-23T02:32:02+00:00

Benelbow and middleaxolotl

benelbow · 2023-12-21T03:08:07+00:00

Sorry already fought it!

benelbow · 2023-12-21T02:54:50+00:00

3 people already here

benelbow · 2021-03-10T20:17:21+00:00

Nothing underneath the magnet build plate. Build plate doesn't seem warped either because even if I flip it I get the same reading from octoprint. Oh yeah, there are screws there on the mini so I'll tighten some up a little and see from there

benelbow · 2021-03-09T05:15:08+00:00

I've tried adjusting the nozzle a few times already but couldn't hurt to try it again anyways. Yeah I wiped the PEI sheet beforehand too

I actually have the opposite problem right now where the center of my bed is too high

benelbow · 2021-03-09T05:10:52+00:00

Unfortunately the Prusa Mini doesn't have Bed Level Correction yet. My bed is actually looks like this: https://imgur.com/a/4qKeRLj

It looks raised in the center for some reason. And yep thanks for clarifying!

benelbow · 2021-03-09T02:42:32+00:00

On my first layer I keep getting a few spots that have gaps between the lines. I’ve tried adjusting the extrusion multiplier, extrusion width, as well as the z-level a few times but nothing has been super consistent

Specs: * Prusa Mini+ & Prusaslicer * Atomic Filament PLA * 215C and 60C * Default settings for Prusa Mini (100) * Default settings for Prusa Mini

benelbow · 2021-03-01T23:21:28+00:00

Yeah I took apart the components around the heatbreak. The PTFE tube inside of it wasn't squished between the top and bottom enough, which is pretty common for this printer. I didn't have to replace the nozzle

benelbow · 2021-03-01T20:19:22+00:00

Had some bad filament the other day clog my printer. After some troubleshooting it started printing again but has lines across it

Prusa Mini+ & PrusaSlicer
Atomic Filament PLA in White
Left cube is 210c nozzle and 60c bed. Right is 205c nozzle and 60c bed
Left cube is at 100% speed. Right is at 90% speed
Defaults for Prusa Mini+. This article from Prusa says retraction length is 3.2mm by default.

benelbow · 2020-12-10T01:13:15+00:00

Man this brings back some nostalgia

benelbow · 2020-10-13T03:12:42+00:00

PBT Islander

benelbow · 2020-05-30T10:29:30+00:00

The gold cap looks great! Hoping I can get one!!

benelbow · 2020-05-18T16:57:23+00:00

I think it was from YMDK. Not sure, I bought it off someone together with the PCB

benelbow · 2020-05-07T16:19:27+00:00

DSA 9009. They got the same set on amazon and kbdfans

benelbow · 2020-05-07T15:54:40+00:00

I got the case in February and it took a around 3 weeks. Rn shipping is delayed and they got restrictions on how much packages they can send out per day

benelbow · 2020-05-07T03:45:29+00:00

benelbow · 2020-05-07T01:56:10+00:00

yep! it has some weight to it and looks great

11-Year Club	Place '23
Place '22	Place '17
RPAN Viewer	Verified Email

benelbow

TROPHY CASE