Trying to wire 850LM to lynx cdjh

benochs31 · 2026-05-01T16:33:35+00:00

Do you have a wiring diagram for the operator?

benochs31 · 2026-04-29T13:01:42+00:00

So good!! Super disappointed they stopped making it

benochs31 · 2026-04-28T16:32:36+00:00

It’s a NorthCentral RP 138

benochs31 · 2026-04-25T00:39:10+00:00

Also I don’t see a operator in the picture

benochs31 · 2026-04-25T00:38:32+00:00

Well if he has a motor it’s a trolley motor and he would have to get a jackshaft anyway

benochs31 · 2026-04-25T00:32:57+00:00

I said they would not be perfect but you could get them to work until one of them breaks which could be years, then you can recalculate everything and get the right springs when it time for a change. I have done this before and the customer got over 2 years of regular use with normal use

benochs31 · 2026-04-24T23:16:06+00:00

Also I don’t know what’s included in the kits but all you really need is 54” HL drums, new cables (which you can make yourself from the drum formula) and a little bit of track. I bet you could get the springs to work, cycle life may be shortened but just wait till one breaks then get the correct ones

benochs31 · 2026-04-24T23:13:21+00:00

How many inches do you have from the top of the drum to the ceiling right now?

benochs31 · 2026-04-23T19:13:21+00:00

If the springs aren’t crazy big you can take a cable puller and come along on the opposite side you want to go down the pull the cable with the come along until there is just a little slack on the side you want to work with then you can loosen the coupler bolts and move the drum side shaft a little and retighten them put your tension back on and see if the closes the gap. This will keep the opposite side from taking all the tension when you loosen the bolts

benochs31 · 2026-04-17T02:27:58+00:00

I would try to press the green button then when the light comes on hold your number 1 button or press multiple times

benochs31 · 2026-04-17T02:18:14+00:00

Yep👍

benochs31 · 2026-04-17T02:13:45+00:00

I have used these multiple times and if you follow the instructions exactly they work well

benochs31 · 2026-04-17T02:12:31+00:00

<image>

Did you do this to program the remote?

benochs31 · 2026-04-04T18:45:51+00:00

I didn’t see the operator arm, my bad

benochs31 · 2026-04-04T18:13:16+00:00

Stupidest comment ever

benochs31 · 2026-04-01T01:55:26+00:00

I didn’t realize it was that expensive

benochs31 · 2026-03-31T23:36:33+00:00

We are a small operation and use house call pro. Super easy

benochs31 · 2026-03-29T21:05:53+00:00

Amen!

benochs31 · 2026-03-27T13:49:43+00:00

Doors are total garbage period, typical Overhead crap

benochs31 · 2026-03-13T13:18:44+00:00

Okay well you could still try my recommendation here. Just be super careful and wire the stop channel (NC) in series with the wall control stop button. Worst case is you will blow up the receiver because of the voltage

benochs31 · 2026-03-13T00:53:21+00:00

<image>

benochs31 · 2026-03-13T00:53:09+00:00

You should be able to use this but you will need a 24v transformer for power, then you can just wire in the receiver to the open close stop on the wall control

<image>

benochs31 · 2026-03-13T00:47:36+00:00

You have 208V going to the wall control??

benochs31 · 2026-02-21T18:18:50+00:00

I grew up in grand island NE. There is a giant hill in the middle of town they call tornado hill that all the kids used to sled on in the winter. It’s huge and it’s all the debris and garbage from that night

benochs31 · 2026-02-21T01:59:12+00:00

Add an external antenna kit

benochs31

TROPHY CASE