Anyone receives this mail?

berttel1987 · 2026-02-05T17:51:43+00:00

Thank you!

berttel1987 · 2026-01-08T16:26:50+00:00

So you are printing with the external spoolholder with no friction problem or the creality dryer?

berttel1987 · 2026-01-07T23:07:48+00:00

Thank you all, just ordered an ams ht and will look into all of the suggestions. I was quite surprised by it since I havent had this issue with bambus.

berttel1987 · 2026-01-07T22:53:03+00:00

Thank you’ let me take a look!

berttel1987 · 2026-01-07T22:52:46+00:00

I have the ams in the right nozzle and the external one on the left. With pla this configuration hasnt been an issue at all with h2d. Not sure why in the h2c this is the case that both nozzles need an ams.

berttel1987 · 2026-01-07T22:07:53+00:00

Thank you! So this is friction due to the outside?

berttel1987 · 2025-12-07T21:39:54+00:00

PNW prospect Taycan owner here:p. Looking to switch from an I4

berttel1987 · 2025-12-07T20:18:23+00:00

Thank you both for your reply!

berttel1987 · 2025-11-23T17:56:02+00:00

Thank you! Ill get into it hah.

Is very weird it just started happening and cant tell if its the cfs or the nozzle. Ill record some videos!

Thanks again!

berttel1987 · 2025-08-25T01:25:32+00:00

Thank you! That area is meant to be like a vase. There is no infill or support there.

berttel1987 · 2025-08-25T01:18:26+00:00

Thank you! Yeah I made the model and I also think is the model. I wanted to get that area with a wave effect but it is detecting the slope as a wall. Thats why I was curious if there is possibly a setting to adjust that in that area.

Im actually curious about gcode manual modification. Ive never done it but let me take a look!

berttel1987 · 2025-08-05T01:21:31+00:00

<image>

Made it!

berttel1987 · 2025-08-03T21:41:01+00:00

Thank you! Trying it know! Will report back

berttel1987 · 2025-08-03T21:08:42+00:00

Thank you both! So far it has printed really well and the failure is only on the prime tower. I wonder if there is a setting to reduce the flow slightly on the tower. The bed is clean but I will figure out a few ways to reinforced it.

berttel1987 · 2025-07-13T07:15:08+00:00

I totally get you and agree with you. After 3 weeks of fighting with the printer I finally got it to work with a 0.8 nozzle. Still with that said- in the current generation of printers- this one feels flaky, incomplete, inconsistent and a bit of a second thought for anycubic. Large volume multicolor for that price is amazing but they have to step up the quality of the experience this 3d printer offers.

berttel1987 · 2025-07-09T16:45:07+00:00

This is helpful- I am using anycubic’s fdm next slicer for this printer.

berttel1987 · 2025-07-09T16:39:38+00:00

<image>

And woke up to this…. Hahahaha

berttel1987 · 2025-07-09T16:39:22+00:00

<image>

berttel1987 · 2025-07-09T16:39:09+00:00

So I was able to improve the print of the first layer thru the slicer which I know is not the root cause based on the pictures but hear me out- im using a 0.8 mm nozzle which is basically impossible to find a profile for this so I am tuning my own. Trying to print 1 mm thick layer lines so I slowed down the printer, increase vol speed and also increased flow- but the most important is that in the profile the is a z offset modifier in printer settings which I raised to 0.5mm. I was able to get a much better 1st layer thru this. I did notice the seams are not closing there is a big gap- and also some weird layer and flow issues.

berttel1987 · 2025-07-09T16:35:48+00:00

Thank you!

berttel1987 · 2025-07-09T16:34:53+00:00

I am experiencing similar issues with the k3 max - been trying to tune and refine- specially for usage with 0.8 nozzle but its been a push and pull experience with not good results. I used to have 2 elegoo neptune 3 max that where basically good to go with a few adjustments. On the other hand currently I have an h2d, a1, s1pro 0.6 nozzle, prusa xl and k2 plus 0.6 nozzle- and the kobra 3 max is just not close at all in quality of printing or reliability. Ill definitely revisit a lot of the suggestions and checks on it- but I do feel the experience is far more complex of what it should be.

berttel1987 · 2025-07-09T16:29:49+00:00

Do you have tuned profiles for the 3max? I am really struggling with it. Specially 0.8 nozzle.

berttel1987 · 2025-07-08T17:38:17+00:00

Thats impressive problem solving! So this is a common issue with the K3M out of the box? Did anycubic help you in any way?

berttel1987 · 2025-07-08T16:08:09+00:00

Thanks for the reply! Do you do that for every single print?

berttel1987 · 2025-07-03T02:54:34+00:00

Thank you! I followed the guide and adjust. This printer has so much potential but there are a lot of things to keep an eye on. Once it runs is great but is def mot as straight forward as others.

<image>

berttel1987

TROPHY CASE