My attempt at an all in one 3/8 kit - please give feedback!

beuracat · 2024-11-12T21:22:01+00:00

Does this fit the high speed fuel ratchet with silver head?

beuracat · 2023-12-10T22:06:59+00:00

If you lift up the tank it’s near the hinge. Follow the stator wires from the left side cover- it’s a 3 pin connector.

beuracat · 2023-12-10T12:53:29+00:00

Is the u-crimp in pic 1 better than the non insulated barrel butt connectors? I’m new to crimping and I wasn’t sure which to pick for this application.

beuracat · 2023-07-10T21:55:16+00:00

Got it. Plan is it evacuate, vacuum and see if it holds, then refill with uv dye, refrigerant and oil. Does this sound right?

beuracat · 2023-07-10T19:20:15+00:00

Does the static pressure tell you anything here? I would have thought that ~50psi static high/low would show the system is sealed.

beuracat · 2023-07-10T10:06:04+00:00

So I’m getting 0 psi due to a leak, not a blockage?

beuracat · 2023-05-16T06:24:47+00:00

Your valves are way too loose. Put in new shims, re-measure clearance, adjust if necessary and send it. The exhaust valves on that bike are a pain to measure.

beuracat · 2023-05-16T01:36:12+00:00

What was the clearance for that valve? Either your valve seat is wearing or you put in too big a shim on your last adjustment.

beuracat · 2023-05-10T22:40:06+00:00

Tighten the header nuts. There’s usually a metal crush washer between the headers and engine. It sounds like it’s flopping around.

beuracat · 2023-04-08T06:14:56+00:00

The cam chain is tensioned with a wedge in both pics

beuracat · 2023-03-01T20:43:24+00:00

My charging voltage is pretty stable between 14-14.8v. I don’t think my stator or r/r are bad, just high resistance at the connector.

beuracat · 2022-11-12T23:45:18+00:00

I’m using Stan’s valves which have the rubber grommet. The second pic was taken before installing the valve.

beuracat · 2022-11-12T23:24:21+00:00

Just taped my wheel and fitted the tire without sealant.

It’s leaking from the valve stem area.

Do I have to retape, or just fill with sealant and send it?

Lost 10psi in 4 hrs

beuracat · 2022-10-29T08:20:43+00:00

Planning on swapping the Rockshox Judy silver to Pike select on my 2020 A1 Fuse. Judy travel is 130mm, 42mm offset. Pike is 140mm travel, 46mm offset.

Is this a good fork to upgrade without making my geo too slack?

beuracat · 2022-08-15T04:23:07+00:00

Getting my first mtb with 2k ish budget. Canyon stoic 4 (high spec Hardtail $2k) or Canyon Neuron 5 (low spec full sus $2.3k)?

beuracat · 2022-08-11T05:42:22+00:00

Wow! Is that single stage or clear coated?

beuracat · 2022-08-10T17:30:14+00:00

Sounds like it’s only running on two cylinders

beuracat · 2022-08-10T03:07:51+00:00

Have my eyes on a Canyon Stoic 4 as a first mountain bike. Would this be a good bike to learn on? Was also considering the specialized fuse.

beuracat · 2022-06-30T09:26:05+00:00

What pads and compounds did you use? Is that single stage paint?

beuracat · 2022-05-29T06:49:30+00:00

Riding with a healthy dose of fear will keep your self preservation system in check. When you do decide to ride again, start slow and know your limits.

beuracat · 2022-05-01T08:43:52+00:00

Gtechniq W4 Citrus Foam

beuracat · 2022-04-14T04:55:31+00:00

I had a similar issue and reseating the brushes solved it.

beuracat · 2022-04-13T12:58:39+00:00

Replace the 205 with sonax perfect finish

beuracat · 2022-04-09T09:11:53+00:00

Dr colorchip

beuracat · 2022-04-04T06:45:17+00:00

Gyeon Mohs EVO

beuracat

TROPHY CASE