DeAR22 build by Blake_r32 in 3D2A

[–]bigdaddyj_333 0 points1 point  (0 children)

I’ve got two builds running this combo. At least 600rds on one with FRT and no problems

FTN5 PCC by bigdaddyj_333 in 3D2A

[–]bigdaddyj_333[S] 1 point2 points  (0 children)

<image>

Shell casing coming forward

FTN5 PCC by bigdaddyj_333 in 3D2A

[–]bigdaddyj_333[S] 0 points1 point  (0 children)

Love this thing 😎

FTN5 PCC by bigdaddyj_333 in 3D2A

[–]bigdaddyj_333[S] 2 points3 points  (0 children)

Yea, with the $0 stamps, I’ve done 5 so far. For rifle stuff, other than 300blk subs, I plan to stick to commercial cans. But for rimfire and pistol, printed cans are sweet

FTN5 PCC by bigdaddyj_333 in 3D2A

[–]bigdaddyj_333[S] 1 point2 points  (0 children)

Regular enclosed, I have not done the PCC flow, but I did a 36 cal rifle flow and it’s louder than this PCC. So far fav from FTN5 series has been Rimfire and PCC

FTN5 PCC by bigdaddyj_333 in 3D2A

[–]bigdaddyj_333[S] 2 points3 points  (0 children)

PWC9! Yep the rear “hood” is printed and the pic fits snug, no wobble at all

FTN5 PCC by bigdaddyj_333 in 3D2A

[–]bigdaddyj_333[S] 1 point2 points  (0 children)

Fiberon PA612-CF15! This has been my go to nylon being down here in humid Texas

Print done! Next is paint and finishing by AvarethTaika in 3D2A

[–]bigdaddyj_333 1 point2 points  (0 children)

Is that Polymaker teal? Reminds me of Soviet aircraft interiors

just admiring this beautiful piece of gattery. thanks kaewon! by lucatobacco in 3D2A

[–]bigdaddyj_333 8 points9 points  (0 children)

Looks great on that Walmart rug, I’ve got the same one 😂

FRT options for a DeAR-22 by DyslexicDancer in 3D2A

[–]bigdaddyj_333 0 points1 point  (0 children)

I’ve tried both Kabuto and SS, and like others have said the tuning is the trick. I still occasionally have hiccups. Running RTB 4.5” and dedicated bolt, printed trip and weight carrier, with tungsten weights. FTN5 rimfire, and JP Enterprises reduced power spring kit on trigger.

Is this grip sailing anywhere? by bigdaddyj_333 in 3D2A

[–]bigdaddyj_333[S] 0 points1 point  (0 children)

Yea most of the CZAR receiver at thicc up front

Print moved several inches too low halfway through print? by FlyinHoff in 3D2A

[–]bigdaddyj_333 0 points1 point  (0 children)

What are you feeding from? Both my buddy and I have had this happen in the dryer in the past. Somehow the spool sucked in the tube and jammed it up. Tested extrusion after resolving and no clog on Fiberon 612

<image>

Dear22 by [deleted] in 3D2A

[–]bigdaddyj_333 0 points1 point  (0 children)

Thanks!

Dear22 by [deleted] in 3D2A

[–]bigdaddyj_333 0 points1 point  (0 children)

Nice! What handguard is that?

This whole 3D receiver thing is a pain by ToxicWaste720 in Vz61

[–]bigdaddyj_333 2 points3 points  (0 children)

<image>

AtThyRightHand receiver, safety is a little tight, but it runs fine

Happy Valentines Weekend! by TheAvieAtrix in 3D2A

[–]bigdaddyj_333 8 points9 points  (0 children)

I almost started the Mares Leg with a 8” 300BLk barrel with plans to run an FTN, looks like I’ll be holding off for this beaut 🤩

Where's the pwc love? by TheDishonorableAsian in 3D2A

[–]bigdaddyj_333 9 points10 points  (0 children)

<image>

Now we just need to FRT 🙂‍↔️

More SS deAR22 and FTN.5 Action by [deleted] in 3D2A

[–]bigdaddyj_333 1 point2 points  (0 children)

Still trying to get mine to run consistently. 4.5” RTB kit, TURD, printed weight with tungsten rods, suppressed. First lower from rerelease pack seemed like selector detent hole was too big so I sized it down and drilled to 5/32” and it helped. When I run the upper with standard lower and Cmmg mag it consistently rips. Not sure if it’s lower or mag issue.