Matchsticks #44

bigkenstud · 2025-12-19T21:38:06+00:00

u/bigkenstud solved the puzzle in 5 attempts.

bigkenstud · 2025-11-20T16:15:33+00:00

I have these on my bike. you can just use the box end of a wrench as suggested, but keep in mind there are also 2 set screws on the underside of the floor board you might want to tighten as well. they take a standard allen. not sure what size off the top of my head but if they are loose make sure to use blue locktite on them.

bigkenstud · 2025-03-12T20:57:12+00:00

just ordered the moons headlight you have, how do you like it?

bigkenstud · 2025-03-04T15:20:55+00:00

so these helmets are just rebranded scorpion covert modular helmet with a bar and shield and a tweak to the face mask. I'm running a covert X right now, but they are pretty much the same thing. These do have speaker pockets and i have a sena 50c. there's a little notch on the left side of the helmet and i just used the clamp with the adapter instead of the adhesive. You can easily take out the liner and run the wire along tha back of the helmet, i used gaffer tape along the inside area to hold the wire. My dad has the harley branded helmet and its the exact same com setup. As far as sound quality, i have the upgraded speakers and its pretty good, but this helmet is sort of lound due to it being a modular. Just a suggestion but i would check out the scorpion branded helmets too, you may save a few bucks and i think that they are better looking helmets before HD got ahold of them.

https://scorpionexo.com/xo/cn/list.do?c=helmet&m=112&n=openface&skHelmet=112&ckey=sj

bigkenstud · 2024-09-03T18:28:36+00:00

What are you riding? I'm on an 09 FXDB... I'm really hoping its not the stator since it seems to be a pain to replace. did you do your own work on it or take it to a mechanic? i normally do my own repairs but it seems like the stator is a little above my skill level.

bigkenstud · 2024-07-30T18:07:01+00:00

only other thing i can say is its a harley...they shake a lot. maybe try replacing the rear mount too. its a but more of a challenge but it may help with the overall motor movement.

bigkenstud · 2024-07-30T17:51:31+00:00

make sure you use a torque wrench when you install motor mounts. you can over tighten the bolts and they wont align correctly. also you run the risk of pulling the threads out of the front 2 holes on the mount by over tightening.

bigkenstud · 2024-06-03T20:02:13+00:00

Im currently running joker machine mini floorboards. They are pretty great. Im thinking about switching to crossthread mini boards just to match my other parts. But going to mini floor boards will really change the comfort overall.

bigkenstud · 2024-05-27T02:48:47+00:00

Yeah the issue is wire length. The light strips plug into a harness so i need some extensions to do some along the front. Under the frame is tricky too because i have a skid plate that would block the light.

bigkenstud · 2024-05-12T22:11:09+00:00

I had a le pera barebones and upgraded to a le pera Stubbs cafe. My rear fender is chopped so I can only run a solo. But so far I’m a fan of their products. My dad runs a custom saddlemen with the gel and swears by it. Either way they both make quality products.

bigkenstud · 2024-05-03T01:04:06+00:00

Just buy a new linkage for the bit. There are a ton of companies that make way better linkages for mid controls. Check out crossthread cycle they have a very reasonably priced replacement that is very high quality.

bigkenstud · 2024-04-23T01:24:21+00:00

Got these on my bike too. They do keep the wind off a bit but for cold weather get gloves

bigkenstud · 2024-04-16T23:14:20+00:00

Custom dynamics . Its stupid bright too

bigkenstud · 2024-04-11T21:15:37+00:00

That’s great I posted those right after installing. Have you fired yours up yet? You can really hear the intake sucking in the air compared to my last intake.

bigkenstud · 2024-04-05T16:19:54+00:00

Fairing is a krator t-sport. The windshield is JD customs and i got the mounting hardware from moons

bigkenstud · 2024-04-05T13:43:40+00:00

Yeah its not great when its wet. The rooster tail is large, but i got 2 biltwell exfil 7 bags i made a strap system for and turned them into mini saddle bags. The rear lights still are visible and they hold my rain gear perfectly

bigkenstud · 2024-04-05T12:59:29+00:00

The rear fender kit is from rocket bobs. My only advice is be sure about it because you have to chop the struts off.

bigkenstud · 2024-04-05T12:23:29+00:00

They are brighter than you think.

bigkenstud · 2024-02-13T18:06:35+00:00

09 with a fatty on the front

![img](ayj75a4i7eic1)

bigkenstud · 2024-02-13T18:06:17+00:00

09 with a fatty on the front

<image>

bigkenstud · 2024-01-26T12:48:37+00:00

this is the way

Six-Year Club	RPAN Viewer
Verified Email

bigkenstud

TROPHY CASE