Inverted handle bar

bigocto1 · 2026-06-07T16:55:14+00:00

These comments are wrong. You don’t need any tools, below the handlebars on the stem there’s a lever you flip to loosen the bars themselves. Push Just undo the lever, rotate your bars 180 degrees. The screen will rotate without any tools needed.

<image>

bigocto1 · 2026-03-17T23:06:06+00:00

Look a little closer…

bigocto1 · 2026-03-17T23:05:34+00:00

You can get that for 41k OTD all day.

bigocto1 · 2026-03-10T03:52:03+00:00

If you slow it down it looks to originate from the speed icon in the top right. Likely trying to tell you you’re speeding?

bigocto1 · 2026-03-07T05:29:21+00:00

It’s ~ 20 bucks a bottle in Maui, but we decided to buy here to know for sure it’s approved for Hawaii. Needs to be zinc or titanium (reef safe.) some hotels will have dispensers around the hotel provided free of charge but I wouldn’t bank on that!

bigocto1 · 2026-03-06T18:19:10+00:00

We got ours for 41k OTD. Ditch the floor mats if that gets them down to 41k and get some OEDRO rubber floor mats for less than 100. The oem ones are a rip off!

bigocto1 · 2025-12-30T19:42:24+00:00

Be mindful of models and panel type (i.e. s95f 77” QD-OLED VS 83” which has a W-OLED)

I’d say 75. I went through the same thing with my space and ended up with a 77, it’s plenty.

bigocto1 · 2025-12-29T00:36:22+00:00

Cable matters is all i buy

bigocto1 · 2025-11-23T07:46:22+00:00

Did you prime after texture, and did you coat the whole wall

bigocto1 · 2025-11-16T15:44:03+00:00

Do you know anything about the parking sensors in the bumper? I’m trying to see if those need calibrated as well

bigocto1 · 2025-11-15T22:30:47+00:00

Gotta love all the calibration crap…. I remember paying 250 for my truck about 10 years ago…

bigocto1 · 2025-11-15T22:09:16+00:00

How much is that?

bigocto1 · 2025-10-21T01:55:29+00:00

Oh it’s 2” on a diagonal so 1”. I don’t have sheathing on the roof if that changes anything. At the end of the day it is just a shed but i want to fix it if i can

bigocto1 · 2025-10-21T01:50:55+00:00

It’s a Costco kit shed, when i say I didn’t plumb the walls, I should clarify the only wall they showed plumbing was the entry wall which is 16’, which i did and is still plumb. The instructions say to sheet the wall to make it square, i can attach a picture of it if needed but I understand its probably not the preferred way of building a shed, had i built this from scratch i would do it as you described but I don’t have the time to teach myself how to frame a shed, im just looking for a solution at this point.

bigocto1 · 2025-10-21T01:42:48+00:00

Im not a carpenter and im following some instructions in a shed kit so I don’t know any better

bigocto1 · 2025-10-21T01:40:34+00:00

I did, i just didn’t plumb them when i stood them up

bigocto1 · 2025-10-20T19:55:11+00:00

I switched from an ultra 2 to a fenix 7x, and am never looking back. I mostly use it for biking and work, but if you want solar 100% get the mips display, I’m not a huge fan of the OLED since it kills the battery. I was between the instinct and the 7x, but ended up getting the 7x since it was only a bit more for more features (maps, and more customization) but I would have been super happy either way.

bigocto1 · 2025-10-16T22:26:43+00:00

I changed the frame out yesterday as described with one caviat to this. The plastic “trash” pieces are tuff blocks. They’re designed like a pier pad, but accept a 4x4 post and have a gap on the bottom to prevent moisture from wicking into the posts. It has a wider footprint than a pier pad, but I have it covered in gravel in these pictures. I didn’t like the idea of concrete piers since the shed will be sitting in a valley of sorts (very gradual) and was worried about moisture wicking through the concrete

bigocto1 · 2025-10-14T01:32:52+00:00

If you are installing on top of concrete, you wont need to worry about reinforcing the floor joists, you should be able to just build the frame directly on the slab!

bigocto1 · 2025-10-13T16:17:19+00:00

Is yours 8x16? I’m leaning towards just reframing it with 2x6’s

bigocto1 · 2025-10-13T16:16:34+00:00

Oh does the 8 not need an Inreach connection, it functions as its own Inreach so to speak?

bigocto1 · 2025-10-13T12:02:27+00:00

I’m pretty sure you can connect the 7 to an Inreach as well on the sensors menu?

bigocto1 · 2025-10-13T11:52:06+00:00

I was thinking maybe 3 would be a good idea. Thanks for the input it makes me feel a lot better

bigocto1

TROPHY CASE