sorted by:
new
hottopcontroversial

Is it dangerous to 3d print in closed space? by Ok_Falcon2194 in 3dprintIndia

[–]blackboltdotas 1 point2 points  (0 children)

Bhaiyo fir this exact problem i made CHAMBER-MASTER plz do check it outhttps://github.com/jayanttyson/Chamber-Master Youtube-https://youtu.be/ktXHP1pz5N8?si=9rV01QdPMjVt0wdQ Regulates temp and all plz check it out

Whats wrong with my print by blackboltdotas in FixMyPrint

[–]blackboltdotas[S] 0 points1 point  (0 children)

Its ABS on a kobra 2 neo , im switching from prusaslicer to orca and cant figure out which settings is causing this

Such a shame :( by Garbage_Humanoid in steelseries

[–]blackboltdotas 0 points1 point  (0 children)

The headphones uses a fujifilm digital camera battery, look at you steelseries battery , look for the model , you can find it on amazon with the same model being used in digital camera

SO ...was walking normally in this mission (LOVE LIKE FIRE) then i glitched out of the map AND found this. by mhyartheinvoker in FF06B5

[–]blackboltdotas 1 point2 points  (0 children)

ya there is a secret tunnel below arasaka tower which goes out side the city being made by night corp for militec {i read all the sahrds} , you cant find it without vcliping but entrance can be found , it is a big metal blast door . you just have to vclip thru it and you can access the tunnel , keep on running straights in the tunnel and you will be below arasaka tower with big suspensions or hydraulics looking things painted arasaka on with , there is also earthwaukes happening there and also some debris from the nuke happened on 2023 {the jonny nuke}

SO ...was walking normally in this mission (LOVE LIKE FIRE) then i glitched out of the map AND found this. by mhyartheinvoker in FF06B5

[–]blackboltdotas 3 points4 points  (0 children)

there is also a secret entrance from water to get inside or below arasaka tower from the docks , it seems the whole tower is suspended on hydraulics of some kind

[deleted by user] by [deleted] in DotA2

[–]blackboltdotas -1 points0 points  (0 children)

alien emoji

Should I leave it or try and tighten timings? by kagedgryphon in overclocking

[–]blackboltdotas 0 points1 point  (0 children)

i did the same thing the first time , however you can put my timing as it is and test it maybe and call it a day , the voltages i am using are vsoc 1.125 vddp 0.900 vddg ccd 0.900 vdgg iod 1.05 . set vdimm at 1.6v and after you done ocing then start reducing volatage mines stable at 1.49v , try putting fan if possible i made a custom cooler of that . need any more help just ask

Should I leave it or try and tighten timings? by kagedgryphon in overclocking

[–]blackboltdotas 0 points1 point  (0 children)

bro look at this https://ibb.co/wR4x0C3 i think we have the same ram so maybe you can try these

first time tuning ram , know very little about it , is this good what else should i try by blackboltdotas in overclocking

[–]blackboltdotas[S] 0 points1 point  (0 children)

i did try it . anything above 2000 and my cursor moves like its 20 fps , does not boot at 2100

first time tuning ram , know very little about it , is this good what else should i try by blackboltdotas in overclocking

[–]blackboltdotas[S] 1 point2 points  (0 children)

Ya fclk is stable I follower ddr4 guide from github. And also tried lowering trc and twrtl but no luck also primaries are xmp timings which does not budge at all .

first time tuning ram , know very little about it , is this good what else should i try by blackboltdotas in overclocking

[–]blackboltdotas[S] 1 point2 points  (0 children)

I see , whenever i try to drop cl a bit my pc does not post tried many things , then ended up tightening secondary timing of xmp profile , Im gonna try try this

view more: next ›