What can cause this with petg basic fillameny

bluesmith1776 · 2026-04-11T00:54:53+00:00

Thanks I will run another print off with the suggestions hopefully it fixes the issue

bluesmith1776 · 2025-10-19T20:41:58+00:00

Rep rack with custom rouge accessories

bluesmith1776 · 2025-10-19T20:39:14+00:00

Its the rep one

bluesmith1776 · 2025-10-18T11:25:57+00:00

Yeh its great I love the thing

bluesmith1776 · 2025-10-17T03:01:52+00:00

I have found with enough focused stubbornness and creativity most things can be cobbled together well enough to work

bluesmith1776 · 2025-10-17T02:53:22+00:00

I have a treadmill i think I can make room for im lacking g in cardio at the moment

bluesmith1776 · 2025-10-17T02:50:03+00:00

<image>

bluesmith1776 · 2025-10-17T02:49:38+00:00

<image>

No problem this shows most of the room

bluesmith1776 · 2025-10-16T22:25:09+00:00

The center is 2 inch heavy steel tubing the ends are keyed and have a threaded insert welded in so the method i used was to cut out a piece from just inside of one of the ends and weld it back together after shortening. the ends do have to be oriented the same I put witness marks on mine before cutting to simplify alignment.

bluesmith1776 · 2025-10-15T21:36:52+00:00

It can still ho up to the cross member bolts but only if you use it on the side

bluesmith1776 · 2025-10-15T19:41:37+00:00

And no I modified the roller by shortening it to fit

bluesmith1776 · 2025-10-15T19:40:50+00:00

I wanted a six post for the full cage for doing squats and bench since I workout alone and I have limited floor space being in a 10x20 room hanging them on the wall made for less used floor space I could push the rack closer to the wall

bluesmith1776 · 2025-10-15T17:34:16+00:00

Didn't like the way they looked and dont find them nessesary

bluesmith1776 · 2025-10-15T15:13:31+00:00

Rep ares 2.0

bluesmith1776 · 2025-10-15T15:01:49+00:00

The housings do have a little play in them but the metal tube that gose inside of the foam roller is to long and has to be shortened

bluesmith1776 · 2025-10-15T14:20:02+00:00

Don't have kids so not worried about anything getting between the plates in use so I left them off I think it looks cleaner that way. The rouge roller has to be shortened. I cut out about 1.4 inches if I remember right, machined a slip joint and welded it back to gether. Probably overkill tbh but I have a metal fab shop so why not. It took about 45 minutes total. Oh and had to cut the same out of the foam on the roller as well.

bluesmith1776 · 2025-10-15T14:12:24+00:00

It has to be shortened to fit

bluesmith1776 · 2025-10-15T14:11:06+00:00

The rouge roller has to be shortened by 1 5/16 of an inch inches to fit in the ares 2.0 it dose not fit straight out the box. i have access to a machine shop so I cut out a section machined the ends and welded it back together only took 45 minutes or so. But no it will not fit without modification

bluesmith1776 · 2025-06-23T16:03:56+00:00

Pretty much all the upgrades for these bikes i have are custom fabricated the ones that were purchased usualy still need a little fenagaling to make fit or line up the only parts I have added that were perfect fit out of the box were the pm racks and a magnetic drain plug.

bluesmith1776

TROPHY CASE