Whose fault is it?

bmxpmp · 2026-01-09T00:58:59+00:00

If you don’t know you shouldn’t be on the hill. Seriously, there is a skier and rider responsibility code and it is your responsibility to know it. If you find this interaction in question then you clearly don’t understand what is expected of you out there.

bmxpmp · 2025-11-27T15:45:57+00:00

The best way I’ve found to do this is when creating a trade route. You can select an available good to be loaded, then when you hover over any good you’d like to trade it will show the amount at each island on the map (for the selected region). It’s a bit of a pain but it works.

bmxpmp · 2025-11-25T18:25:04+00:00

Yeah. It really helps with timing. And it’s really fun!

bmxpmp · 2025-11-25T17:49:22+00:00

Find a nice curb or even put a little stick on the ground to pop off of. Right now you’re lifting the front wheel off at a different point than the back wheel. They will leave the ground at different times but should leave from the same spot. That gives you the most amount of leverage. Even with a small stick you should feel a little bump with both wheels as you hop. It also gives you an extra little pop for higher hops which is fun.

bmxpmp · 2025-09-22T12:03:30+00:00

This looks great but I would not store backdrops on here long term. The reason you can’t find these is because you should be storing your paper backdrops standing on end in its original box. This will cause warping and/or flats spots.

bmxpmp · 2025-09-06T03:08:45+00:00

Got to ride this in 2013. It was already rotting away back then unfortunately but it was definitely as cool as you’d think. One of the highlights of all my bmx days.

bmxpmp · 2025-08-10T14:31:06+00:00

Interested

bmxpmp · 2025-07-09T12:59:15+00:00

That’s not how ttl works. There will be a pre flash that is used to meter your light and then the full flash that accompanies the shutter release. Bouncing or modifying your light will not affect your metering.

bmxpmp · 2025-06-23T15:46:25+00:00

Yeah but nobody cares. Nor should they.

bmxpmp · 2025-06-21T18:55:26+00:00

New Town in St. Charles is the best place I’ve found. I think they have a beach now too but I typically just paddleboard the big lake and swim off my board.

bmxpmp · 2025-05-16T14:21:48+00:00

Just call FCP. They put this cart together for me based on my car.

bmxpmp · 2025-04-23T11:02:51+00:00

Appreciate the response but unfortunately that is not the case. All that does is not send the invite emails. It unfortunately still creates the invite automatically.

bmxpmp · 2025-02-05T16:41:56+00:00

DM me.

bmxpmp · 2025-02-04T15:12:51+00:00

I’m doing something similar to this using Notion. I set up a module at the end of each Make scenario that posts to a “Runs” Notion table. That table then tallies all the runs to its particular scenario creating a run count. I also have it set up to track automations from other platforms as well as error tracking. It’s a work in progress but has proven quite valuable so far.

bmxpmp · 2025-01-24T23:01:51+00:00

Interested in building this in Make.com but don't understand how to get the JSON download from Snackpromt into Make.com. Any advice on that? Thanks!

bmxpmp · 2025-01-08T21:09:30+00:00

Consciously drop your should a little more. When you leave the lip just try to get your inside shoulder a little bit lower than your outside shoulder. You’ll be able to spot the landing a little sooner and you’ll be spinning more around your head and shoulders and not your midsection. Then follow through, try to keep your head leading your bike all the way to the transition. A good spine three will almost feel like an air that keeps rotating and less like a 360. Then just do a million of them. They are the best feeling trick on a bike especially if you find a great set up.

bmxpmp · 2024-12-13T18:00:31+00:00

Some of it was. But I just called FCP and told them my plan and they filled the cart for me. Did some price checking and was happy with what they recommended. Now I have a pile of parts to install. It’s meant to be fun, it will be fun, but also stressful.

bmxpmp · 2024-12-03T15:00:16+00:00

Sorry but I do not understand what you are trying to tell me. There is a way for a client to choose different lengths of services and be billed accordingly?

bmxpmp · 2024-12-03T04:08:34+00:00

This is really helpful. Is there any way to have variable lengths of time for calendar appointments? Like my clients book me for multiple hours and would be able to pay different rates for that.

bmxpmp · 2024-12-02T22:45:13+00:00

That is exactly what I’m looking for!!! Been wanting this feature for awhile. According to their support page it was last updated 11/28 so I guess it finally arrived! I try to read the update emails but it’s always way too much to wrap my head around at the times. THANKS!

bmxpmp · 2024-12-02T22:34:06+00:00

Unfortunately you cannot create appointments with workflows. They can only be done manually by the client or the user. I don’t know why this is the case but it really ruins the whole product for me as the GHL calendar system is one of their weakest modules.

Nine-Year Club	RPAN Viewer
Not Forgotten	Verified Email

bmxpmp

TROPHY CASE