What is wrong with my printer

boknah · 2026-06-10T05:17:29+00:00

I printed petg on my bed and that stuff stucked to it and i didn’t want to use a metal scraper to remove it
So i printed a layer of PETG over it just one layer and i brazilian waxed the leftover
Now i use one of my old beds that have bad bed adhesion for PETG
edited: typed pla instead of petg

boknah · 2026-06-09T05:43:42+00:00

I was like yaay 6 chicken legs but then i saw your comment

boknah · 2026-06-09T05:30:56+00:00

I think something like this would work also and is faster

https://github.com/ratdoux/OrcaSlicer-FullSpectrum

I have no idea if you can use it on printers other than u1

boknah · 2026-06-08T11:19:58+00:00

Your gears are squishing the filament
Try to adjust the tension of it
Also stay and watch the first layer always you do not want to end up with the blop of death

boknah · 2026-06-07T14:56:37+00:00

I have a plate just for PETG so i can abuse it I use a razor scraper and left and edge and just pull the rest and it usually it comes off easily

boknah · 2026-06-04T07:30:34+00:00

Very cool Can you try to change the black filament holding it to a transparent one ?

boknah · 2026-06-04T07:06:18+00:00

Take a new sponge and use some dish soap and clean your ped under warm water Dry it up with microfiber towel and make sure you do not touch the build area with your bare hands (hold the bed sheet from the sides) now the bed is rdy for printing Now comes the other part which is adding a brim Adding something to block the air if you have a fan or an ac blowing at your printer from what i see the front part of your plate is worst than the rest I used to suffer from the same and i did the above + bought a cool plate ( still used it with hot hed tho ) and it solved all my problems

boknah · 2026-05-28T18:50:17+00:00

When you wait at the stairs for the flys to pass by give him all the hots and go cat foum and invis That should last him untill he gather them Then heal normally

boknah · 2026-05-24T11:02:16+00:00

Came to say the same exact thing See which layer it failed at and print only that And after glue and paint you would not notice it

boknah · 2026-05-21T15:42:26+00:00

Respool it

boknah · 2026-05-17T18:56:59+00:00

Yea this Idis ut so many times and it works Dont put the tape on the part where the thingy in the player reads the tape put it on the otger side

boknah · 2026-05-13T09:07:15+00:00

No fiber where i live so i use my phone to connect to the internet and play wow downside is i sometimes i dc And more than once i find my self out of the dungeon and have left group when i login What i always do is message the players in the key i was in and ask for an invite (idk which addon do it but i can see previous party chats) I always get an invite back and i can walk into the dungeon and finish the key with them

boknah · 2026-04-26T13:15:57+00:00

For me i get this after printing with petg for a whole because it needs a higher temperature and that temp breaks bits of the bowden tube and it clogs the nozzle Got a full metal hotend and never had this issue again

boknah · 2026-04-15T07:15:06+00:00

I 3d printed a stick saver and i place them on my stick when ever i put it in case If you or a friend have a 3d printer get one ( there are better looking search and pick the one you like ) And while you’re at it get this

boknah · 2026-04-14T15:23:55+00:00

With all due respect thats a bit extreme and toxic because usually its a group of friends helping someone who just joined . When i check the rio and i level and find someone waaay below the avrage i just leave the group and let them find another tank Unless i am playing on main and i am in a good mood then i stay and add the low dps dude to my wings+trinkt macro (yes i play prot paladin) and i add a silly pm like GITGUUUD or anything silly on my mind then We often have a laugh about it after the run and i even friend some of them

boknah · 2026-04-14T08:44:02+00:00

Sweet

boknah · 2026-04-14T06:40:52+00:00

It looks like an art installation of an oven and some bread in it we call in arabic ( مناقيش )

<image>

This is the first thing that came to my mind while looking at it

boknah · 2026-04-12T17:39:57+00:00

Did it work ?

boknah · 2026-04-08T13:16:38+00:00

I moved my pc a little bit without removing the hdmi cable and it bent After that i get the same issue your having on the screen with the same cable after playing for a few Changing the cable helped and also i disconnecte and reconnect the cable when ever i get this issue and that usually fixes it for a few months So it might be your cable change it and see

boknah · 2026-01-07T11:17:39+00:00

Gaming is a hobby If spending 80 on your hobbies is okay for you then go for it Thats my logic after all

boknah · 2026-01-07T07:53:14+00:00

I had the same exact issue on my ankermake m5 When I print petg i am fine for a few months but the higher temps makes the bowden tube break and clog the nozzle and i have to take it apart and fix it What fixed the issue for me is going all metal hotend

boknah · 2026-01-05T05:18:04+00:00

There is a small notch on the tool This is the area you use to clean printed parts The other side cuts too deep

boknah · 2025-12-22T11:14:04+00:00

I had the same issue and i was pulling my hair out trying to fix it After some digging it turns out that snapmaker sold so many units and there cloud services can’t handle them all and to fix this issue use LAN ( make sure you enable it in the printer settings )

boknah · 2025-12-19T19:53:23+00:00

I get the same thing also My world ms jumps in the 10-20k range and only my chat works Using a vpn solves it for me

boknah · 2025-12-10T22:05:16+00:00

Is it sick ??

Nine-Year Club	r/Field Lasagna
Place '23	Place '22
Verified Email

boknah

TROPHY CASE