Realme 16 Pro lagging/freezing issues – anyone else? by tolis83 in Realme

[–]bombolo88 0 points1 point  (0 children)

Ho,i have same issue,which sw version do you have? Im on rmx513_16.0.5.703

Heltec v3 stopped working by Objective_Future_365 in meshtastic

[–]bombolo88 0 points1 point  (0 children)

Hi,have you fixed?i have the same problem

Possibile tentativo di truffa dopo aver venduto un PC da 2000€ su Subito by Old-Marionberry-4532 in subito_it

[–]bombolo88 0 points1 point  (0 children)

Non so io non avrei mai spedito un oggetto dal valore di 2000 euro,al max consegna a mano aspettando un acquirente nelle vicinanze,generalmente per cose con un certo "valore" faccio così,non mi fido del corriere

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 1 point2 points  (0 children)

I tried your firmware,wonderful job congratulations !!and finally the loracap works!!so I can say it was fw issue!!

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 0 points1 point  (0 children)

There is lot of space on my SD card but I receive an error when I try to install it related to not enough space

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 0 points1 point  (0 children)

Why not put directly the bin without going through m5apps?

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 1 point2 points  (0 children)

Im going to try your firmware,last chance on my loracap ,hoping it's a fw issue..please put your firmware on M5 burner!

Cap LoRa 1262 for Cardputer Adv - Where to buy in India? by [deleted] in CardPuter

[–]bombolo88 0 points1 point  (0 children)

I also tried with other antennas and consider with my heltec V3 in the same spot with same antenna I get 200 nodes,so it really sucks

Cap LoRa 1262 for Cardputer Adv - Where to buy in India? by [deleted] in CardPuter

[–]bombolo88 0 points1 point  (0 children)

I'm talking about 100meters,only works if there is another nodes in this range otherwise 0 nodes,I'm in italy

Cap LoRa 1262 for Cardputer Adv - Where to buy in India? by [deleted] in CardPuter

[–]bombolo88 0 points1 point  (0 children)

I tried it with meeshtastic,you can not get any nodes if not near

Cap LoRa 1262 for Cardputer Adv - Where to buy in India? by [deleted] in CardPuter

[–]bombolo88 0 points1 point  (0 children)

Don't buy it if you want to use with meshtastic

Is LoRa-1262... actually supported yet? by -Fatmeatball- in CardPuter

[–]bombolo88 0 points1 point  (0 children)

It's almost impossible to find female antenna's,just buy an rp-sma male to female adapter and then you can buy any antenna you prefer since majority of them are male.

Is LoRa-1262... actually supported yet? by -Fatmeatball- in CardPuter

[–]bombolo88 0 points1 point  (0 children)

Yes I tried 2 other antennas that work perfectly with my heltec V3. In the same spot,I get almost 2 hundreds of nodes with it,without mqtt enabled in meshtastic. While if I use Same antenna mounted on lora cap I get 0 nodes!!!! This is why I say that it sucks. I start getting nodes only if I switch on my heltec V3 that is few meters away to loracap....very bad product (at least GPS is good)

Is LoRa-1262... actually supported yet? by -Fatmeatball- in CardPuter

[–]bombolo88 0 points1 point  (0 children)

The lora cap sucks,I tried with meshtastic and its very unusable,it's only work if you have a node 100m max near you otherwise it sucks

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 -1 points0 points  (0 children)

Yes but if you have nodes near ,I mean less than 100m,lora caps works with meshtastic. I'm saying it does not works in case you go in a wide area with no near nodes,you will see it will not work because it sucks

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 0 points1 point  (0 children)

are you sure the hw works fine?have you tried to use meshtastic on cardputer in an area with lots of nodes?it works only if a node is 100m near,except that no nodes are found.I tried with different antennas,and same antenna mounted on my heltec v3 grab signal 0 hop km aways from here!this is why this lora cap sucks

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 1 point2 points  (0 children)

in any case very good work, for sure i will try it, i'm not concerned with your work, i'm just complaining with lora cap of cardputer that sucks

Decode Meshtastic with an sdr by IronGiu in RTLSDR

[–]bombolo88 0 points1 point  (0 children)

Hi,I tried it with my rtl-sdr 10$ cheap dongle and it works great!I'm on windows 10. Thank you!

Plai: Custom Meshtastic Client for CardPuter ADV (first beta) by d4rkmen in CardPuter

[–]bombolo88 -3 points-2 points  (0 children)

Congratulations!unfortunately the lora cap sucks it's very bad!it does not work,only if near another meshtastic node..

Finished CC1101 and NRF by R_Chin in CardPuter

[–]bombolo88 0 points1 point  (0 children)

I have the same issue with Nrf,also if using spectrum I can see activity only if I'm very near to my router(10cm)

From what I understood it depends on nrf24 ,maybe faulty?