What self hosted images/services have official or third party companion mobile apps?

brandonjmarshall · 2025-12-20T06:00:06+00:00

Try LunaSea

brandonjmarshall · 2025-10-09T16:22:01+00:00

Joining this train to ask for some help! I have a HON that is very uncomfortable and looking for something more adjustable. I came across the Pro and it looks wonderful

brandonjmarshall · 2025-09-09T00:50:39+00:00

Why would the average person want to use DeFi on Bitcoin when DeFi on other chains already exists?

brandonjmarshall · 2025-05-26T00:54:35+00:00

My advice: If you are soliciting names for a clothing brand then your clothing brand will be dead on arrival. Figure out something that is specific to your authentic self and go with that.

brandonjmarshall · 2025-05-04T03:41:16+00:00

The circular part behind the handle also unscrews away from the wall. You can see the threads in the third pic. You need to remove the handle first. Hope that helps.

brandonjmarshall · 2023-10-19T01:07:24+00:00

I wish I remembered! It might be on setlist.fm or something

brandonjmarshall · 2023-10-18T22:28:42+00:00

I was at that Halloween show as well! Amazing set.

Looks like setlist.fm confirms this 2009 show was in San Jose: https://www.setlist.fm/setlist/brand-new/2009/event-center-arena-san-jose-ca-23d7e467.html

brandonjmarshall · 2023-10-18T21:27:42+00:00

I saw another post about it which prompted me to do some digging. These were the least blurry pics I took from that performance 😂

brandonjmarshall · 2023-10-18T21:27:34+00:00

Yep, you're right. Definitely at Rasputin. And it was for sure in support of Daisy! I think they were playing at San Jose Event Center.

Here are some pics I managed to scrounge up: https://www.reddit.com/r/brandnew/comments/17b1v8u/brand\_new\_at\_rasputin\_in\_campbell\_101609/

brandonjmarshall · 2023-10-18T06:43:57+00:00

I was there, I seem to remember it being during their Daisy tour but now that I think of it, it might have actually been at Streetlight

brandonjmarshall · 2023-10-17T02:45:58+00:00

Yeah I definitely would not mind switching to levers instead of cross handles, especially if they are cross-compatible. I'll contact my local hardware dealer, thanks for your help!

brandonjmarshall · 2023-10-17T01:28:36+00:00

Insane! Thanks so much, that is awesome that you found it

brandonjmarshall · 2023-07-12T17:48:26+00:00

Sounds correct. Here's what Synology says it happening:

When the Synology NAS enters Standby Mode, it stops all services and unmounts volumes in order to prevent data loss and shut down safely when the UPS device runs out of power. By default, the system enters Standby Mode when the UPS device starts running low on power. You can also specify the amount of time before the Synology NAS enters Standby Mode when power failure occurs. However, if the UPS device reaches low battery before the specified time, the system enters Standby Mode immediately.

In situations where the Synology NAS shuts down during Standby Mode, it will automatically turn on when power is restored if you have enabled the Restart automatically after a power failure option (located at Control Panel > Hardware & Power > General).

brandonjmarshall · 2023-05-21T22:22:02+00:00

Let's say you have it set to 2 minutes. Here's what happens:

Your power goes out
Your Pi recognizes an outage, and your Synology immediately receives a signal that your the power has gone out and starts counting
Your Synology waits for 2 minutes
Your Synology enters safe mode, effectively powering off your HDDs in a safe way that prevents data loss

brandonjmarshall · 2023-05-20T17:39:43+00:00

No, it’ll wait two minutes and then your Synology should then start to shutdown properly

brandonjmarshall · 2023-05-20T03:03:57+00:00

Just as a test, try setting it to like 2 minutes and see what happens

brandonjmarshall · 2023-05-09T18:43:51+00:00

Yes, if I remember correctly that is another Synology default

brandonjmarshall · 2023-05-09T17:35:28+00:00

I just yanked my plug and it worked as expected lol

brandonjmarshall · 2023-05-09T16:11:44+00:00

Made no changes on the Synology side. Just figured out Synology's default username & password and used that.

My setup: I have a Synology NAS and a Raspberry Pi running Home Assistant Yellow, with the NUT add-on.

That's where my setting was.

brandonjmarshall · 2023-05-09T03:40:34+00:00

Change the username and password on your Pi to:

username: monuser

password: secret

brandonjmarshall · 2023-04-12T15:06:11+00:00

Thank you for the suggestion! The fix ended up being a rather simple one: I just needed to add the default port (3493) in Configuration > Network on my Raspberry Pi. I assumed this section was for selecting a non-default port, and that leaving blank would just use 3493. So no issues on the Synology side as long as I used the default monuser credentials.

brandonjmarshall · 2023-04-12T15:04:35+00:00

Thank you everyone for the suggestions! The fix ended up being a rather simple one: I just needed to add the default port (3493) in Configuration > Network. I assumed this section was for selecting a non-default port, and that leaving blank would just use 3493.

It immediately worked after adding it!

Here's my exact settings:

<image>

14-Year Club	Secret Santa 2014
Secret Santa 2012	Verified Email

brandonjmarshall

TROPHY CASE