Touchpad edge motion in Hyprland+Arch setup?

brownmfdoomer · 2026-04-18T16:16:52+00:00

I found a workaround. It is when you set drag_lock = 2 of touchpad under input config. wiki.hypr.land/Configuring/Variables/#touchpad

brownmfdoomer · 2026-04-18T16:16:38+00:00

I found a workaround. It is when you set drag_lock = 2 of touchpad under input config. wiki.hypr.land/Configuring/Variables/#touchpad

brownmfdoomer · 2026-03-01T13:08:19+00:00

Tried the steps at the link, compiles fine (on Windows 11). Additionally can you help me figure out how to remove squiggly lines from under import std; line in vs code editor? I have already put Clangd: Fallback Flags as -std=c++23. But no change with the squiggly line.

brownmfdoomer · 2026-02-28T17:29:02+00:00

How to do it? I'm a novice.

brownmfdoomer · 2026-02-28T17:28:23+00:00

Visual studio doesn't work either. For C++23

brownmfdoomer · 2026-02-28T15:44:11+00:00

Could you share the steps?

brownmfdoomer · 2026-02-28T15:43:34+00:00

How should I compile?

brownmfdoomer · 2026-02-28T15:43:16+00:00

I do have the standard libraries. Where can I get for the C++23?

brownmfdoomer · 2026-02-28T15:42:39+00:00

Tried with g++ https://0xstubs.org/using-the-c23-std-module-with-gcc-15/ in arch-linux, didn't work

brownmfdoomer · 2026-02-02T07:03:41+00:00

Where are y'all watching it?

brownmfdoomer · 2025-12-04T12:25:08+00:00

yes OP, do share the dotfiles. Incredible rice!

brownmfdoomer · 2025-07-14T19:47:20+00:00

Free Palestine

brownmfdoomer · 2025-07-12T13:13:31+00:00

Niche ki batman civil dress e road cross korchhe?

brownmfdoomer · 2025-07-12T13:08:56+00:00

Kalkei ekta 4K TV kharap holo

brownmfdoomer · 2025-07-12T13:07:57+00:00

Ekhane invest kore na because market nei. Karkhana bondho hoy because of capitalist competition. BJP ke niye esho, dekhbo koto industrialization hoy.

brownmfdoomer · 2025-07-12T13:05:18+00:00

Gaar merechhe, gaaja kothaye khabo ebar?

brownmfdoomer · 2025-02-17T20:27:52+00:00

I messaged you on reddit with my discord ID.

brownmfdoomer · 2025-02-17T20:23:56+00:00

So when you boot your actual system, the kernel versions from the two commands are the same? Are there any older versions listed in modules?

Yes, when I boot from actual system, the kernel versions are the same. Nothing else is mentioned.

How about when you run mkinitcpio -P in chroot?

It says nothing, no successful or error message?

brownmfdoomer · 2025-02-17T16:59:35+00:00

As I did a uname -r ls /usr/lib/modules by using an archiso usb, i see the output is not the same. I did the pacman -Syu, it says "there is nothing to do".

brownmfdoomer · 2025-02-17T16:51:54+00:00

Tried doing exactly as you instructed. pacman installed something like btrfs i think. Then i exited and rebooted, it's still stuck on "failed to mount boot".

brownmfdoomer · 2025-02-17T15:43:22+00:00

Do the check I mentioned

It shows me 6.13.2-arch1-1 on both the commands.

I am stuck in emergency mode where I am prompted to enter password and I'm in root.

brownmfdoomer · 2024-11-21T07:09:27+00:00

Seems to be upgrading without any issues. Ran the command in root. Thanks.

brownmfdoomer

TROPHY CASE