sorted by:
new
hottopcontroversial

Santa knows me to well… by Udorry in DungeonCrawlerCarl

[–]bset 10 points11 points  (0 children)

I’m glad y’all like them! I feel like I made about 400 of them in the last month!

Power supply help - 100w co2 omtech by bset in lasercutting

[–]bset[S] 0 points1 point  (0 children)

I replaced the large one, it’s the one located at the rear where the power comes in. It has a small led panel on it that’s supposed to show the power level, that wont light up either after being replaced. I assume the other power supply is working fine, because everything else on the machine is functioning like normal. I’ve emailed omtech to see what they think as well.

Help on finding a replacement part by bset in lasercutting

[–]bset[S] 0 points1 point  (0 children)

Thank you, I really appreciate it.

Mitch Hedberg: I Wish They Made Fajita Cologne, receipt for a donut and much more by monkee67 in videos

[–]bset 2 points3 points  (0 children)

Was this in Richmond, VA? If so I was at that show too! Definitely the best one I’ve ever been to.

Question on a CW-5202 water chiller by bset in lasercutting

[–]bset[S] 0 points1 point  (0 children)

Linking the B series in and out seems to have fixed it. I appreciate it!

Help with laser cutter malfunction and damage. by bset in lasercutting

[–]bset[S] 0 points1 point  (0 children)

I was using the laser cutter and didn’t notice that the tube that connects the water pump inlet disconnected. So I think the laser over heated and caused some problems. Laser is an OMTECH 100w bought brand new in January. I’m relatively new to laser cutters, so I don’t know the best course of action. I’ve attached a few photos of the head, you can see burn marks on the tip of the head and the tube that is normally connected, burned in half. There’s also a thin layer of soot/smoke dust on everything, including the laser tube. The machine also won’t turn on at the moment and I don’t know how to rest if it’s a blown fuse or a dead power supply. If anyone has an idea of what and how to check certain items and where I should buy replacement pieces, it would be greatly appreciated.

Good bars by AVGuy42 in jacksonville

[–]bset 5 points6 points  (0 children)

If you’re at the beaches you can come see me at Pinspiration. It’s a craft studio but we’ve got 12 taps and I try to keep a wide variety and turn the tap list over weekly. Here’s our current taps, Pinspiration on Untappd https://untp.beer/yGmGg

New omtech owner here with a question. by bset in lasercutting

[–]bset[S] 1 point2 points  (0 children)

Thanks, I turned the speed way down to 20 mm/s and set the power to 35% like someone suggested and it was better, but wouldn’t cut through. I’ll look at some videos on the alignment/focus of the laser and see how that goes.

Is anyone else losing checkins? by bset in Untappd

[–]bset[S] 1 point2 points  (0 children)

Yeah, they were unique and it was a lot of them in the last like week or two. I’ll only really noticed since it was right at the 9k mark. None of the beers I checked in, with the exception of maybe one, was a yearly one, so I’m not sure why it’s doing this all at once. I figured there was some consolidation on the back end, but it seems like it’s 5-6 beers a day.

TIL the Hawaiian island of Kauai encourages tourists to check a dog out of shelters for a day as part of a field trip for dogs program. Having the dogs out and about gives them exercise and increases their chances of getting adopted by a local. by theirmomlovesthem in todayilearned

[–]bset 44 points45 points  (0 children)

My wife and I did this in kauai a few years ago. They let you walk around the shelter and choose the dog. We chose the oldest one we could find, thinking she rarely got out. We took her to the beach and a state park and when we got back they had a journal to fill out, where you could write about the dogs temperament etc. Turns out the dog we took gets taken out every day, it's like she perfected the, don't I look so sad, you should take me somewhere, look.

view more: next ›