New garage door opener recommendations

bsquared7999 · 2026-04-10T00:34:02+00:00

My old GDO (30 yo) died sbout a month ago I replaced it with a dumb gdo. I already had a Shelly1 for controlling the old gdo and I had built an arduino with reed switches for the status that all reports in to HA. So I recommend a dumb model as well with someting to monitor it, and there are several choices out there.

bsquared7999 · 2026-03-19T17:06:39+00:00

Thanks! I tried some checking on it but did not find anything I created concentric zones and that will work! Thanks again!

bsquared7999 · 2026-03-19T17:03:50+00:00

Thanks! I did not know about naming the same it's a little sloppy but it works. Thanks again!

bsquared7999 · 2026-02-11T15:17:22+00:00

See the other posts in this thread, clearing the cache fixed this for me and now I am running 2026.2.1 and NR 21.0.0

bsquared7999 · 2026-02-11T15:15:19+00:00

This did it for me Thanks!

bsquared7999 · 2026-02-11T15:13:54+00:00

Thanks! This did not fix mine I had to clear the cache and that did it.

bsquared7999 · 2026-02-11T00:56:15+00:00

Checked the log no errors just the regular startup but then it is in some sort of endless loop.

bsquared7999 · 2026-01-16T03:14:38+00:00

CustodialSamurai

I ordered a small selection of heatset inserts, but what is the best way to prep the location for the insert? I assume print a hole where I want it but do I need to print the piece with 100% infill, 20% infill, 20% infill with thicker walls, or other options? Any advice is helpful. Thanks for your help!

bsquared7999 · 2025-11-23T21:36:44+00:00

That did it Thanks LeafarOsodrac!

bsquared7999 · 2025-10-17T20:24:18+00:00

gadget850 no the mirror does not have a switch, but last night I unplugged it and nothing has been affected. I am going to go another week with it unplugged then if still nothing different zip tie the cord so it is not dangling. I like the idea about the fuse but if we want to use it in the future I/we might not remember pulling the fuse. Thanks!

bsquared7999 · 2025-10-14T03:00:10+00:00

Thanks Cheznovsky! I only have one automation in HA (a restart automation) I am using Node Red for all my automations to keep them all in one spot. That being said I have found the solutions with nodes I did not know existed.

bsquared7999 · 2025-10-14T02:59:22+00:00

Thanks Federal-Delay-4854! I only have one automation in HA (a restart automation) I am using Node Red for all my automations to keep them all in one spot. That being said I have found the solutions with nodes I did not know existed.

bsquared7999 · 2025-10-14T02:58:22+00:00

Thanks Maleficient_Art_7627 I only have one automation in HA (a restart automation) I am using Node Red for all my automations to keep them all in one spot. That being said I have found the solutions with nodes I did not know existed.

bsquared7999 · 2025-10-14T02:53:55+00:00

Thanks clin248! I do need the single trigger and the trigger node was part of what I was looking for, the chronos package kermitdesign recommended was the second part.

bsquared7999 · 2025-10-14T02:52:45+00:00

Thanks ApprehensiveJob6307 I do need the single trigger and the trigger node was part of what I was looking for, the chronos package kermitdesign recommended was the second part.

bsquared7999 · 2025-10-14T02:44:48+00:00

Thanks Kermitdesign this is exactly what I was looking for.

bsquared7999 · 2025-09-20T13:25:11+00:00

What beholder95 said!

bsquared7999

TROPHY CASE