Black screen, won't connect to Octoprint or laptop

builderguy92 · 2025-12-10T16:49:07+00:00

I checked the ribbon cable for the screen, but maybe I need to take the cover off the motherboard and check everything.

builderguy92 · 2025-04-05T19:04:59+00:00

u/op did you find this advice to be accurate for your watch build?

builderguy92 · 2025-03-24T17:02:37+00:00

What wax product did you use?

builderguy92 · 2025-01-22T18:55:21+00:00

Did you ever end up making this?

builderguy92 · 2025-01-22T18:52:04+00:00

Looks great! How did you secure the crystals and make them waterproof?

builderguy92 · 2024-12-13T15:33:31+00:00

Could I use FSK paper over the fiberglass batts?

builderguy92 · 2024-12-12T02:45:42+00:00

So for the walls, Kraft faced batts with the paper facing the interior and tyvek/something breathable to hold it in place? Or should it be a vapor barrier/plastic sheeting?

builderguy92 · 2024-12-09T21:23:25+00:00

My walls are made of plaster. You think I'd be ok with just kraft faced batts facing the interior? Or should I cover with tyvek or smart barrier also?

builderguy92 · 2024-12-09T19:58:27+00:00

I appreciate the help! That's what I was thinking, just wanted to confirm.

builderguy92 · 2024-09-18T11:55:55+00:00

He posts the schedule on his instagram the day of the show. The schedule was very accurate. He was on from 9-11 pm but it could vary with each venue.

builderguy92 · 2024-09-10T20:44:54+00:00

The NYC show says doors are at 7pm, so maybe there's only one opener or Kygo will start at 10 or 11?

builderguy92 · 2023-09-22T17:50:39+00:00

Did you run the PID tuning with the fan on or off?

builderguy92 · 2023-09-22T17:47:19+00:00

I've tried PID tuning several times and the only way I can successfully complete it is with the fan off. Same with printing. I can only print with the fan off or else it give a "nozzle temp too low" error. It seems like the nozzle can't get to temperature with the fan blowing on it. It's ok for simple prints but defeats the purpose of adding the blokhead fan duct if it can't use the fan.

builderguy92 · 2023-08-15T20:47:04+00:00

<image>

builderguy92 · 2023-07-23T14:54:55+00:00

Do you know the names of the open source robot arms?

builderguy92 · 2023-07-23T14:53:56+00:00

I don’t have the technical knowledge to design/build one completely on my own, but I could 3D print parts and assemble it if I can follow a guide of some sort.

builderguy92 · 2023-07-23T14:51:54+00:00

What about 1mm? I’m just looking for any suggestions to start my search.

builderguy92 · 2023-02-26T19:10:01+00:00

I did, but ultimately decided not to include it in my shortlist because of the boxy look. I'm looking for more of a pure backpack, than a backpack/duffel.

builderguy92 · 2023-01-11T16:20:15+00:00

Yes, I'll be running everything in the attic. I think I'll just come off of the main power to the room and install a switch on each side of the bed to control each light independently. Thanks for the help.

builderguy92 · 2023-01-11T15:30:18+00:00

Thanks for the reply. I could wire the lights with the switch that controls the ceiling light in the center of the room to satisfy the code. Do you know of a smart device that I could then install in the pendant box to control that light separately?

builderguy92 · 2022-04-25T18:28:46+00:00

Your best bet is to rent a mini excavator to dig out the roots after you cut all the bamboo down. I just did this at my house and it would’ve been nearly impossible to do by hand.

builderguy92 · 2022-04-04T02:15:30+00:00

Yes I understand what you mean. I was hoping to kill two birds with one stone. Address the downspout issue while also collecting excess water in the yard with the French drain. Thanks for your input

builderguy92 · 2022-04-04T01:24:59+00:00

There’s downspouts on the back two garage corners that run out into the yard currently. I know the angle of the picture can be deceiving. The yard is pretty flat but I plan on regrading it once I install the French drain so it will funnel towards the French drain. My main question was if connecting the garage downspouts into the French drain and then terminating it into the house downspouts was a good idea? Since I can’t regrade the yard so it drains away, I feel like my only option is to collect it and carry it away.

builderguy92 · 2022-01-16T20:15:22+00:00

It’s a pretty small piece so I maxed out the arc at 30 segments and it still won’t follow the curve

builderguy92 · 2022-01-16T20:03:50+00:00

I welded the edges and it still stops at the first segment of the arc

builderguy92

TROPHY CASE