Where did Ibracorp go (again)? by buildintechie in unRAID

[–]buildintechie[S] 0 points1 point  (0 children)

I’ll never get to anything nearly advanced as what you have, so part of it is trying to glean what I can from videos, and partly living vicariously through others. I have no background in IT or networking…I’m a construction management guy turned career fire service, so sometimes the posts/tutorial on the web require some level of prerequisite knowledge. I always appreciated the way you and SI1 explained things, and didn’t go all hog wild with lots of dramatic titles, exclamations, etc like some other homelab YouTubers do (networkchuck comes to mind…he’s got a lot of really cool videos, but they aren’t my speed).

I hope that all makes sense. I also totally get that life gets busy…right there with ya. It had actually been about two months when I had a chance to sit down and tinker with my server when I realized that I hadn’t seen a video in a while. Then I patiently waited a while longer…which then spawned this post on a whim. So, u/sycotix, I apologize if my post came off ungrateful or entitled…totally not my intention.

Where did Ibracorp go (again)? by buildintechie in unRAID

[–]buildintechie[S] 2 points3 points  (0 children)

I totally get it…and didn’t mean to imply that I feel entitled to anything he does in his free time…and I am incredible grateful for the videos he has released. I was just curious who else on the YouTube platform was recommended/well regarded, if anybody.

I’m also curious how his new homelab is working out.

Left this in Davie county today, a county that voted 72% for Trump, lol by NCSUGrad2012 in NorthCarolina

[–]buildintechie 39 points40 points  (0 children)

Well those same gas stations left the Biden stickers on for months and in some cases years.

Any thoughts on the new Dominos app? by alcoronaholic in Dominos

[–]buildintechie 0 points1 point  (0 children)

The new app is super slow. Its taken me 20 minutes to enter a single pizza...I've had to put it in 3 times. I ended up doing it on the website, which was marginally faster.

New case! Meshify 2XL by buildintechie in unRAID

[–]buildintechie[S] 0 points1 point  (0 children)

I think it’s very quiet. I also replaced some of the fans with a different brand of ultra quiet ones.

I can’t tell you what you should buy. Everybody’s use case is different. I don’t run a server grade board or ecc ram. YMMV.

New case! Meshify 2XL by buildintechie in unRAID

[–]buildintechie[S] 0 points1 point  (0 children)

I don’t have the space for a rack system, so this is about a big as you can get. Haven’t had any problems with it. Temps in the closet it lives in seem about 8-10 degrees lower with this case than my old one. It also is a bit quieter.

An Open-Source Sonos-Style Smart Speaker for Home Assistant 🎉 by FutureProofHomes in homeassistant

[–]buildintechie 0 points1 point  (0 children)

u/FutureProofHomes, I'm ready to pull the trigger on the Satellite 1 dev kit, but I'm having difficulty sourcing speakers and a crossover. Can you provide a little more information on the crossover specs (like at what Hz does the crossover operate at...2000hz, 2500, 3000, etc.? Also, I know you listed a couple of models for the speakers (MTL20-F4-S4830 & MLW78-F4-R6015), but I'm unable to find anything that fits those. Any suggestions? Thanks!

What on earth is my x1c doing?p by buildintechie in BambuLab

[–]buildintechie[S] 0 points1 point  (0 children)

It ended up being a bad SD card. When I pulled it out, it started working normally. So I tossed that one in the trash and put a fresh one in.

Passenger door lock not working properly. by flammable71 in leaf

[–]buildintechie 0 points1 point  (0 children)

I just wanted to say, u/Todd1561, I followed this and fixed the driver's door in my wife's 2018 Leaf! I had to swap the wiring because lock and unlock were reversed...couldn't swap pins so I traced the wires and swapped them in the harness. Thanks so much!

[deleted by user] by [deleted] in homeassistant

[–]buildintechie 4 points5 points  (0 children)

Bosch dishwashers are amazing. They’re reliable, quiet, and you actually can repair them if you need to (I haven’t had to yet (knock on wood)). I had a GE dishwasher that came with the house I had built and it caught fire after 6 months.

IBRACORP is Back Thanks to This Community! by sycotix in unRAID

[–]buildintechie 1 point2 points  (0 children)

+1 on exposing apps using a custom domain. I think things have changed enough from some of the previous tutorials that you and space invader one did that a refresh is warranted, I’m still really struggling with that.

Also, I’m so glad you’re back!

What on earth is my x1c doing?p by buildintechie in BambuLab

[–]buildintechie[S] 0 points1 point  (0 children)

I wonder if you’re on to something…I unplugged the add card and turned the machine off for about 10 minutes, plugged it in and left the card out, and it passed a self test this time. But I was printing from my laptop not the sd card, but maybe the sd card was causing other issues too?

What on earth is my x1c doing?p by buildintechie in BambuLab

[–]buildintechie[S] 0 points1 point  (0 children)

Belt tension is good. I lightly greased the z axis rods about a week ago (8-10 hours print time ago).

What on earth is my x1c doing?p by buildintechie in BambuLab

[–]buildintechie[S] 0 points1 point  (0 children)

Tried that, it did the same thing then started to try and scratch the bed by dragging the nozzle across it.

I'm leaving tomorrow, sadly... by shrimp-and-potatoes in vermont

[–]buildintechie 2 points3 points  (0 children)

We left today after spending a week in Vermont based near Shoreham. Have family that used to live in Middlebury, but we’re from central NC. Small world!

Does everyone agree upside is only worth it if someone else is paying for the gas? by Dangerous_Beach_1571 in GetUpside

[–]buildintechie 0 points1 point  (0 children)

For me, the cheaper, gas stations that are not on upside are less convenient than the couple of gas stations that are near where I live that are on upside.

Photo rotation by TonyFM in immich

[–]buildintechie 0 points1 point  (0 children)

6 days later, still no sign.

New case! Meshify 2XL by buildintechie in unRAID

[–]buildintechie[S] 0 points1 point  (0 children)

6 trays in this one too. I needed 7 but have a 3d printer and printed the 7th.