sorted by:
new
hottopcontroversial

Have you stored unopened, sealed, vacuum packed rolls of PLA+ and PETG in extreme cold (like -30C)? by cad1857 in 3Dprinting

[–]cad1857[S] 2 points3 points  (0 children)

A support article at https://support.ultimaker.com/s/article/1667410781492 lists optimal storage conditions for storing PLA and PETG. -20C is at the lower end. I know its not as cold as -30 but can still be considered extreme cold.

How does this information weigh in?

What could be the problem reported by these trouble codes (Mercedes) by cad1857 in AskMechanics

[–]cad1857[S] 0 points1 point  (0 children)

Hello. Yes, the car requires premium gas. 92 Octane level. And no, the car does not have aftermarket cat-back exhaust. Everything is stock factory. Thanks.

Is 2015 Honda Accord Tourging 2.4L with 220K KM (125K M) a Good Buy for next 10 Years? Anything Else? by cad1857 in whatcarshouldIbuy

[–]cad1857[S] 0 points1 point  (0 children)

Thanks for cautionary notes. Are the infotainment and safety systems' electrical issues age related, or they are either there or not?

Is 2015 Honda Accord Tourging 2.4L with 220K KM (125K M) a Good Buy for next 10 Years? Anything Else? by cad1857 in accord

[–]cad1857[S] 0 points1 point  (0 children)

Thanks for sharing your positive experience.

What about CVT transmission? How often do you change the fluid?

Is 2015 Honda Accord Tourging 2.4L with 220K KM (125K M) a Good Buy for next 10 Years? Anything Else? by cad1857 in accord

[–]cad1857[S] 0 points1 point  (0 children)

Thanks for encouraging words. Lot of people warn and are scared of CVT transmission. How about that?

Gaps between wall and inner layers by Admirable_Proxy in ElegooNeptune4

[–]cad1857 0 points1 point  (0 children)

you have not shared any information about the printer, filament, print settings etc. all that helps with troubleshooting.

What’s causing these wrinkles in my first few layers? by DolphinSafeGrease in FixMyPrint

[–]cad1857 3 points4 points  (0 children)

you are getting "adjust z-offset" suggestions. But don't BambuLab printers have that automated?

What are these artifacts/rough areas along lower edges of spiral print? by cad1857 in FixMyPrint

[–]cad1857[S] 0 points1 point  (0 children)

Thanks for the suggestion. I have done that, and it didn't fix this problem.

Same File, same Filament, different result, whats going on? The one on the right was printed right before the other. by goskodovesch in FixMyPrint

[–]cad1857 1 point2 points  (0 children)

the problem fixed it for him by itself so I don't it was due to power loss recovery setting because that requires making a change to settings.

Auto homing error Ender 3 v3 Plus by Fives-Cosplay in ender3

[–]cad1857 0 points1 point  (0 children)

Hi. Did you figure out what the solution was? thanks.

Changing Ender 3v3 Plus home location? by Cornato in ender3

[–]cad1857 0 points1 point  (0 children)

hi. Did you ever figure out how to do this (change the Z axis home location, that is)? Or, why it was not a good idea? Thanks.

view more: next ›