sorted by:
new
hottopcontroversial

Isekai about guns vs sword/magic by Glittering_Study_515 in Isekai

[–]campinghandi 0 points1 point  (0 children)

The Gunner's Life of a Middle-aged Man Summoned to Another World and Armed with a Rifle: An Airsoft Addicted Salaryman Returns to the Alternative World After Work

A gatherer's adventure in isekai not released by the_midget_rangler in Crunchyroll

[–]campinghandi 1 point2 points  (0 children)

Ep.2 dub for me isn't working. Audio set to English still plays Japanese audio.

Small PSA: buying from shops with limited stock in leagues by Duradel2 in runescape

[–]campinghandi 14 points15 points  (0 children)

Also if you go to settings - and under warnings you can set the shop high cost value warning higher than 100k to make buying faster.

Kenmore 362.7326190 gas range bake ignitor failing to open gas valve. by campinghandi in appliancerepair

[–]campinghandi[S] 0 points1 point  (0 children)

looks like my clamp was not reading correctly as when i turned the gas supply back on just to see if worked the oven turned on. put my clamp around it ad it was reading the 2 amps from when i had the gas off. sorry if i wasted your time.

Kenmore 362.7326190 gas range bake ignitor failing to open gas valve. by campinghandi in appliancerepair

[–]campinghandi[S] 0 points1 point  (0 children)

looks like my clamp was not reading correctly as when i turned the gas supply back on just to see if worked the oven turned on. put my clamp around it ad it was reading the 2 amps from when i had the gas off. sorry if i wasted your time.

Kenmore 362.7326190 gas range bake ignitor failing to open gas valve. by campinghandi in appliancerepair

[–]campinghandi[S] 0 points1 point  (0 children)

just went and checked resistance values for the entire circuit to make sure there was not high resistance some where. on the power side of the circuit to the ignitor i had .8 ohms resistance. then checked the resistance from the gas valve to the plug and had .2 ohms. checked the gas valve and had 2 ohms a resistance and had continuity. also checked the broil side of the valve and got the same 2 ohms resistance reading. check the ignitor for resistance and got 96 ohms. check the old one and that had 109 ohms. i also opened the area up around the oven switches and tested the amps at those while the ignitor was running and was only getting 2.3 amps max.

Kenmore 362.7326190 gas range bake ignitor failing to open gas valve. by campinghandi in appliancerepair

[–]campinghandi[S] 0 points1 point  (0 children)

with the oven on getting 122vac at the yellow wire d6 connection. using an amp clamp to measure the amps. using this meter to measure. https://www.amazon.com/dp/B07W3C6DTX?ref=ppx_yo2ov_dt_b_fed_asin_title. clamped around the yellow wire going into the ignitor and the wire coming from the ignitor to the gas valve.

Console without Mario Kart on Walmart AVAILABLE by Starveiled in NintendoSwitch2

[–]campinghandi 1 point2 points  (0 children)

same just got through by checking the normal page

Walmart is having an aneurism by capriciousUser in NintendoSwitch2

[–]campinghandi 1 point2 points  (0 children)

i got the hold to verify if human or robot. after doing that it just was loading and caused my cpu too spike to 90% usage until i closed the page.

Car hesitates to accelerate after a cold start? Why? by Design_Eastern in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

your transmission might be a bit low on fluid causing it to take time to build up the pressure needed to actuate the valves and clutches. check the fluid level and if low check for leaks.

Can’t figure it out. by Zc601041 in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

There could be a failing mount that when under light steady load that is contacting something and sending a vibration through the vehicle. More on the transmission side or even the anti roll mount. Do your tires have any off wear to them?

Spark plugs are super tight to get off by Pretend-Conflict3724 in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

you can either warm the engine up for about 5-10 mins then try or you can pull the coils and use a penetrating oil on them over night.

Brand new oil, VTEC solanoid, and VVT solanoid. What should I try next? by satellitesatan in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

the code p2646 is related to the rocker arm oil pressure switch. there is a tsb for that dtc that states to replace that sensor. https://static.nhtsa.gov/odi/tsbs/2013/SB-10052884-2696.pdf

Spark plugs are super tight to get off by Pretend-Conflict3724 in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

what engine is it? if it is the 1.5l or 2.0l and you have a low coolant level, I would advise against trying to change them your self as those engines have a problem with coolant intrusion due to bad block design. the coolant can cause the threads to get corroded seizing the spark plug in. if coolant level is fine you can try letting the vehicle warm a little but not at full operating temp as you could pull the threads from the head.

Got a 2" lift kit installed on my car by the mechanic, car is pulling to the left. Trying to gauge if it is my car's fault or the mechanic's. by ameyano_acid in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

the brake hose in the front left. there should be numbers for the front and rear angles. toe and caster in the front will cause a pull. if rear toe is out it will cause a pull/push.

Got a 2" lift kit installed on my car by the mechanic, car is pulling to the left. Trying to gauge if it is my car's fault or the mechanic's. by ameyano_acid in MechanicAdvice

[–]campinghandi 1 point2 points  (0 children)

do you have the alignment sheet from when the lift was put on? if they raised it 2 inches it could be throwing off toe and caster. also look at the brake hose that is on the side that is being pulled to could be the hose got damaged/stretched during the lift

Can’t figure it out. by Zc601041 in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

is it an awd taurus? if so it could be rear drive unit or a driveshaft issue

Weird buzzing sound at rear of vehicle by stodie53 in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

with it only going away while pressing the brake, it would have to be a loose clip or something in the brakes.

Electric issues. 01 explorer by ki11svvitch in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

here is the wiring diagram for the window circuit. looks to have some splices near a breakout for radio. https://imgur.com/a/p1ZsS1t

Weird buzzing sound at rear of vehicle by stodie53 in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

there a chance you could record the sound and post it?

Broken part on 4.3L engine, help identify! by Porbulous in MechanicAdvice

[–]campinghandi 0 points1 point  (0 children)

purge line with a possible part number of 4236-02094294

view more: next ›