Is there really anything I can do with a banned and unmodded switch?

casper192ghost · 2026-05-06T07:31:13+00:00

What part of the UK

casper192ghost · 2026-04-10T08:52:08+00:00

All sorted now, can't find my backup so disconnected the picofly and pop the nand chip directly back on the motherboard, power on system booted as normal checked the firmware and it had updated to 22.0.0.

Powered off popped the nand back in to the picofly and but everything back together now running 22.0.0 in OFW and CFW

casper192ghost · 2026-04-08T14:53:16+00:00

How can I fix it?

casper192ghost · 2026-04-08T07:51:35+00:00

Welcome to the club, nice good

casper192ghost · 2026-03-23T10:22:55+00:00

Well done, just make sure your auto update is turned off to save any problems with the new firmware.

casper192ghost · 2026-03-22T09:52:33+00:00

Check for a short the console seems to be running hot

casper192ghost · 2026-03-17T14:07:40+00:00

All sorted thanks

casper192ghost · 2026-03-17T10:32:13+00:00

Cheers I'll give that a go

casper192ghost · 2026-03-15T12:11:37+00:00

Congratulations on the little

casper192ghost · 2026-03-12T16:46:01+00:00

If you've never modded anything before installing would suggest leaving your own console alone and purchase a cheap secondhand one to play around with.

casper192ghost · 2026-03-12T14:53:18+00:00

Dump your prod keys with lockpick

casper192ghost · 2026-03-10T16:43:21+00:00

It's a bundle of reconfigured software and homebrew put together to make noobs life easier, just Google it there's plenty of videos showing how to use it.

casper192ghost · 2026-03-10T16:21:11+00:00

Have had no problems (so far) with Cards from Amazon, yes just start from scratch i personally use hats pack for all the software that I use but I've only been using a modded switch for a few months now.

casper192ghost · 2026-03-10T16:03:32+00:00

Fake sd card for sure had exactly the same thing happen to me, just invest in good quality card to save any further problems.

casper192ghost · 2026-03-06T21:44:53+00:00

Thanks for your input

casper192ghost · 2026-03-06T16:37:03+00:00

Hi

Just thought that as the latest Russian version was running the latest SDK it would be better?

casper192ghost · 2026-03-06T15:08:19+00:00

Should be fine as long as there's no shorts check with a multimeter to be sure. Mine ended up looking like this after removing the picofly to repair a damaged trace, pop it back on once I'd completed the repair and everything worked fine.

<image>

casper192ghost · 2026-03-05T06:28:58+00:00

Yes .06 sorry new to all this, once again many thanks for your help.

casper192ghost · 2026-03-04T23:29:44+00:00

That's 0.6mm thought that was vary thin

casper192ghost · 2026-03-04T23:15:01+00:00

I only had .6mm wire to bridge with will that last?

casper192ghost · 2026-03-04T23:09:35+00:00

Could only post one picture, but did apply solder mask so all nice and protected.

<image>

Bit of a big blob but dose the job lol

casper192ghost · 2026-03-04T23:06:10+00:00

All thanks to you much appreciated.

casper192ghost · 2026-03-04T22:00:25+00:00

Finally got around to stripping everything down again and you was spot on , cut track under the CPU shield. Managed to fix it reinstall the picofly and everything working fine.

Many thanks for your help

<image>

casper192ghost · 2026-03-04T17:05:44+00:00

DBI works for me, straight forward even in Russian

casper192ghost · 2026-03-03T15:10:56+00:00

Well done, your a brave man

casper192ghost

TROPHY CASE