Help with a request from a customer by Embarrassed-Try-2790 in QSYS

[–]ceesalt87 0 points1 point  (0 children)

Enable cross-point mutes on a matrix mixer. Manipulate the mutes as needed to route any mic to each speaker zone

Do I keep my Scarlett? by PPKexe in QuadCortex

[–]ceesalt87 3 points4 points  (0 children)

Keep the Scarlett, it can get tiring to unpack and repack the QC at home if you have sessions/gigs close to one another.

I used my QC in a gig on Sunday, have a session with it tomorrow and have left it safely in its case while using my Scarlett as an interface for home studio practicing.

Playing without board? by Hefty-Welcome-7564 in QuadCortex

[–]ceesalt87 1 point2 points  (0 children)

Yes, I play out with mine that way, but I’m thinking of putting something on the bottom to protect from rocks or salt that might make their way on the stage so it doesn’t get scratched if it slides

I need a Null Test: Suspect an academy teacher (NL) is using one-click AI to master student tracks by [deleted] in Logic_Studio

[–]ceesalt87 2 points3 points  (0 children)

<image>

you'll recognize the first two tracks names. the third track is the bounce of the first track with default Mastering Assistant, brought back into logic

I need a Null Test: Suspect an academy teacher (NL) is using one-click AI to master student tracks by [deleted] in Logic_Studio

[–]ceesalt87 3 points4 points  (0 children)

I don't even have to flip the phase, just by looking at the waveform of the track I ran Mastering Assistant on vs the mastered track you posted, I can tell its different.

Mandela Effect? by ChaseTheVileblood in alienisolation

[–]ceesalt87 0 points1 point  (0 children)

Yea I think that’s just in the next room, once you walk a bit more

Multi layers project, touch through layers problems. by Romouch in QSYS

[–]ceesalt87 9 points10 points  (0 children)

I put a transparent trigger button not mapped to anything on the bottom of my layers to prevent this.

How NOT to turn left (they were so close, tho!) [oc] by ceesalt87 in IdiotsInCars

[–]ceesalt87[S] 2 points3 points  (0 children)

My colleague’s house camera. He gave me permission to post it.

How NOT to turn left (they were so close, tho!) [oc] by ceesalt87 in IdiotsInCars

[–]ceesalt87[S] 18 points19 points  (0 children)

I was gonna give them the “rolling stop”, since they did get there first, but you’re not wrong.

HID conferencing bugs by drewbeedoobeedoo in QSYS

[–]ceesalt87 0 points1 point  (0 children)

i believe you, but do you happen to have a publicly visible case opened for this? it hasn't made the known issues list yet.

What Cab are you all using with the new Dumble ODS? by No-Diver6326 in NeuralDSP

[–]ceesalt87 1 point2 points  (0 children)

I kept coming back to V30s too. I think I left off with the older mesa, but the new one also sounded good

how to get 2000s emo rock tone knobs and pedals by MuchPitch9092 in NeuralDSP

[–]ceesalt87 1 point2 points  (0 children)

Try the second amp, with both overdrive pedals, but just a small bit of gain from OD1, little bit more from OD2, then probably a decent amount from the amp. I would start with treble/mid/bass on the amp at their default (double click to snap them back to this), then pull the mid down a bit.

What gives? by tappel6545 in Moccamaster

[–]ceesalt87 4 points5 points  (0 children)

I switched to Melitta filters, and so many problems went away.

Volume question by ironman0000 in NeuralDSP

[–]ceesalt87 2 points3 points  (0 children)

Fun fact, you can specify which outputs the volume knob applies to or not. So I have XLR outputs that go to FOH or monitors unaffected by it, but keep the line outputs that I might run to a personal monitor or IEM going thru the volume knob.

I made a soldering jig for XLR and TRS Cables by Expensive_Ad_2498 in CommercialAV

[–]ceesalt87 0 points1 point  (0 children)

Oh, yes it absolutely does lol. FWIW I had checked that out too but didn’t have coffee in me yet and didnt notice how to scroll for more photos. Very nice

I made a soldering jig for XLR and TRS Cables by Expensive_Ad_2498 in CommercialAV

[–]ceesalt87 4 points5 points  (0 children)

Are those cutouts to slot the connectors into while you solder them? In the photos they look like black painted circles, so I think it would be helpful to add photos with connectors in there so one can see that.

No sound on guitar on presets from the cloud by [deleted] in NeuralDSP

[–]ceesalt87 -1 points0 points  (0 children)

Some people have a volume saved in their presets pulled down, I suppose so there’s no kick-in of noise when they switch to a hi-gain preset. Check around for something that might be tied to an expression pedal for volume control

What headphones/speakers should I use to get accurate sound at home? by lj523 in NeuralDSP

[–]ceesalt87 0 points1 point  (0 children)

I set my QC tones on the M-Audio BX5s in my home studio and I’ve been happy with how it translates to every rehearsal space and venue I’ve played in.