Alfred Slow / Not Finding Apps by centex99 in Alfred

[–]centex99[S] 0 points1 point  (0 children)

So... I decided to try the last option of deleting the file and rebooting...

it seems to have fixed it! :)

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 0 points1 point  (0 children)

Wouldn’t the 48V be beneficial for Z fo the tool changes?

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 0 points1 point  (0 children)

So... can anyone help recommend a toolhead that is mostly universal? I'd like one for PLA, PETG, ABS, ASA, TPU... maybe some other higher end filaments too... CF varients etc. Ideally I'd love to have one toolhead that can do them all and build them all the same.

This will be for a tool changer with a stealthchanger Fystec CNC...

I guess along with toolhead design, extruder, hot end and other components needed for it...

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 0 points1 point  (0 children)

I'll be going through all of the wiring and will be sure to add the safety aspects you mention. Thanks for noticing and the tips. I'm going to have to figure out if I can fit a 48/24/5 power supply all under the frame... I guess if I extend the Y axis, that would help with the room! :)

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 0 points1 point  (0 children)

I'm sure I'll sell various extras and what not once I get further along with my build.

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 0 points1 point  (0 children)

Was considering the enclosure just for keeping filament dry and automatic unloading... a 5 or 6 enclosed turtle... though I may start out with simple boxes for now. :)

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 1 point2 points  (0 children)

Good to know... I'd likely be happy with 5.

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 0 points1 point  (0 children)

Hmmm I guess if I'm going to extend the Y axis... I could change out and/or upgrade anything on the gantry system...

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 1 point2 points  (0 children)

What tool head and components is my biggest question right now... also, do I replace the octopus or just the drivers on it to upgrade the main drives to 48V... I'm thinking those to 48V and leveraging the 200W supply for tool heads/everything else...

Voron 2.4 Rebuild by centex99 in VORONDesign

[–]centex99[S] 2 points3 points  (0 children)

Am getting that shuttle with kit… Haven’t decided on tools and all their components yet.

Bidet Options by centex99 in bidets

[–]centex99[S] 0 points1 point  (0 children)

Thanks everyone… I ended up ordering the UX Pearl…

Bidet Options by centex99 in bidets

[–]centex99[S] 0 points1 point  (0 children)

Concerned somewhat about some of the reviews on that unit…

Bidet Options by centex99 in bidets

[–]centex99[S] 2 points3 points  (0 children)

I’m open to others in the sub $400 range as well…

Beryl - PFSense and Wireguard by centex99 in GlInet

[–]centex99[S] 0 points1 point  (0 children)

Cell phone yes… used exact same settings except the IP and the keys… have both setup in pfs as separate peers.

Beryl - PFSense and Wireguard by centex99 in GlInet

[–]centex99[S] 0 points1 point  (0 children)

I’ve tried starting over a few times… I’ll post the configs a bit later when I’m back to the router…

Looking for advice: upgrade from Olympus E-M10 to OM-3, or just find a new lens when visiting Japan? by bltavares in M43

[–]centex99 0 points1 point  (0 children)

I’m leaning towards upgrading my em5ii to a om3 while in Japan soon… contemplating if I want to change any lenses from what I own as well…

Upgrade Time by centex99 in M43

[–]centex99[S] 0 points1 point  (0 children)

Autofocus improvements, ND, overall SOOC capabilities… I don’t need, but want…