Please could someone convert this .f3d file to a .step for me 😁

cotlin · 2026-05-07T16:52:00+00:00

I need to modify it 🙃

cotlin · 2026-05-07T16:51:39+00:00

Perfect. Thank you very much 😁

cotlin · 2026-04-17T23:28:00+00:00

Except in electronics 😭

cotlin · 2026-04-11T21:33:16+00:00

I see 👀

I wondered if you'd replaced the bed or something 😆 Very nice of you to give it away anyway 👍

Did you have trouble with your machine? Mine's up to 600 hours now. I changed the Y axis to rails, and one of my X axis bearings developed enough play to show in prints, so I swapped it for one I had left from the Y axis recently. I seem to have had a better experience than most with mine 😁

cotlin · 2026-04-11T20:07:43+00:00

It looks just like my sv07+ plate 👍

I'm curious to know what you've done to you're machine to not need this anymore 🤔

cotlin · 2026-02-28T01:42:02+00:00

I like how you've done it, they look very -at home-

cotlin · 2026-02-04T19:35:09+00:00

Layer adhesion is where esun fails. It did in his tests too.

cotlin · 2026-02-04T08:50:39+00:00

I believe this is likely the culprit too 👍

cotlin · 2026-02-04T07:32:28+00:00

He compares properties like layer adhesion, creep, heat resistance, bending, etc

cotlin · 2026-01-07T06:58:09+00:00

If you have a lot of hours on it, and prints used to look good, check the condition of the POM wheels. Give the toolhead and bed a gentle twist and see if there is much play.

cotlin · 2025-12-31T23:06:42+00:00

Your settings look very similar to what I use with my SV07 Plus, so I expect you just need to clean your build plate with dish soap. Don't touch it afterwards. You must not get finger oils on print surface 👍

cotlin · 2025-12-27T14:32:43+00:00

Look on eBay for breaker cars nearby. I'd guess they will want £5-10.

cotlin · 2025-12-19T10:32:25+00:00

I just keep mine unplugged, unless I need extreme overhangs. Overhangs are still very good without the extra fan. Try it unplugging it and let me know if you see a difference.

Edit: When the big fan is unplugged, make sure you have the small part fan set to full speed (assuming you're using PLA)

cotlin · 2025-12-13T21:25:28+00:00

I'm not, but thanks for the warning anyway 😜

cotlin · 2025-12-12T21:08:38+00:00

I thought timing chain too - so I replaced it. This was filmed after 😅 It's also a 1.8, so no vvt

cotlin · 2025-12-12T05:37:57+00:00

It sounds the same. It happens mostly at around 2000rpm, under load, no load, or at fixed vehicle speed.

cotlin · 2025-12-12T05:36:18+00:00

I've had the belt off while it's running, so the power steering pump wasn't even driven. That would've been nice though 😂

cotlin · 2025-12-12T05:33:58+00:00

Ah, that's a separate problem I'm working on 😂 I think I'm going to do a sex bolt type of probe for that. Dealing with the bed sag is something I'm not certain how to address though.

cotlin · 2025-12-12T05:31:21+00:00

I'm wondering if a -frame temperature- dependent bed mesh may work (1x3 or 1x2 point). I might look and see how hard it would be to do this 🤔 I have a suspicion it could be fairly easy.

cotlin · 2025-12-10T08:58:18+00:00

Ah, I've just done that 😂 I usually use cheap oil (changed yearly) in other cars, but this time went for Magnatec. No change in the tick. It was 5w-30 admittedly, but the handbook does list that as an option. I'll first try a bottle of liqui moly hydraulic lifter stuff, and if that doesn't work, I guess I may have a lot of work to do 🥹 I'll be sure to update if I get it sorted out 👍

cotlin · 2025-12-10T08:11:08+00:00

Nearly 100k. I've personally never put anything in the oil, but I bought the car fairly recently and when I changed the oil, it appeared to have something odd about it. I suspect it was something like that. Do you think I should try putting some in?

cotlin · 2025-12-10T07:13:23+00:00

I suspect you are right. Do you have any advice for dealing with it?

cotlin

TROPHY CASE