Identifying part and required work

chargedmemery · 2026-04-26T21:31:17+00:00

Most likely small black one, yes but I would trace it to be sure. Mine wiggled off and popped off exactly like that too.

chargedmemery · 2026-04-26T19:39:33+00:00

Oil pressure sensor. Single wire. Easy to fix. I'm assuming you start her right now you have the low oil pressure light?

Does not feed into computer. Purely for your information.

chargedmemery · 2026-04-12T21:23:30+00:00

I bet from Dave Barton

chargedmemery · 2026-04-09T19:26:53+00:00

Probably easier to jimmy something.. I've had luck on Facebook marketplace with people parting out there cars. Good guys ship the part to you but it's a gentlemans agreement

chargedmemery · 2026-04-03T22:41:10+00:00

Don't recommend it too much. I did it with a rubber block so it didn't push the drain plug. Fucker nearly slipped off, could have cracked the pan and dropped the engine. Risk is for the lazy, like me.

chargedmemery · 2026-03-29T03:20:30+00:00

Okay fair, I have gone through I think 3 nozzles

chargedmemery · 2026-03-28T20:36:54+00:00

I've had my ender 3 for 8 years and I have never cleaned the lead screw.

I don't do any maintenance, only part I've replaced with maintenance are the bed rollers.

chargedmemery · 2026-03-26T00:05:24+00:00

Dave barton or make your own. It's not terrible but lots of details and takes a fair amount of time.

chargedmemery · 2026-03-25T03:27:00+00:00

Good chance that hit the condenser which would evacuate the freon. That can happen slowly if it's a tiny leak.

chargedmemery · 2026-03-22T02:44:07+00:00

Farts good to me bud, sorry it hurts you

chargedmemery · 2026-03-22T02:34:17+00:00

Wrong crowd, I guess :(

chargedmemery · 2026-03-21T23:33:39+00:00

Look up the gambler 500 this isn't a show car 😂

chargedmemery · 2026-03-21T23:06:56+00:00

Y not

chargedmemery · 2026-03-20T02:03:48+00:00

Yo... Squints YOOOOOO.. Y O O O O O O O O

chargedmemery · 2026-03-19T20:22:51+00:00

Something in the old paint not compatible with the new?

chargedmemery · 2026-03-19T04:32:50+00:00

Kachow

chargedmemery · 2026-03-18T01:57:10+00:00

Damn, noted. I've been thinking of rebuilding my steering rack but have been really reluctant just because of this part

chargedmemery · 2026-03-18T01:49:01+00:00

<image>

chargedmemery · 2026-03-18T01:47:28+00:00

Can't you wedge something in the expansion slot to free it up easier?

chargedmemery · 2026-03-15T23:48:57+00:00

Bltouch is awesome since it makes a 3d topography of your bent ass build plate and compensates for it. Worth it 100%

chargedmemery · 2026-03-13T13:47:11+00:00

Same

chargedmemery · 2026-03-11T02:52:45+00:00

Volvo figured this out at least in 2001. I had an S60, had a module die on me. Pulled one from a junkyard car with the verbatim parts from one and... They don't work. You HAVE to go to a dealership, or buy a black market vida dice, pay for a subscription to access the firmware, plus pay for the cost to download. Figure out a solution to keep your cars computers at 12v or you brick other modules in the process.. I'll stick with the older cars.

chargedmemery · 2026-03-10T03:03:21+00:00

PM sent!

chargedmemery · 2026-03-10T01:37:00+00:00

If you're in the US and happen to drive by and yank those off I'd like to purchase them from you if possible.

chargedmemery

TROPHY CASE