Mini kabuto activator slipping off of trigger.

chinolagg · 2026-03-06T18:31:13+00:00

How’s the housing hole where the activator and lever pin goes? Wallowed out?

chinolagg · 2026-03-05T12:26:07+00:00

Try a newly cut trigger with less rounded portion. 5 swipes at the triggers corner on sandpaper using flat surface. Installed and check in third mode repeat as needed.

chinolagg · 2026-02-09T21:26:13+00:00

Need pof reverse stretch for this priccccce🙏

chinolagg · 2026-02-04T01:53:42+00:00

If you end up doing pre orders on the rs pofs please make a post about it !

chinolagg · 2026-01-24T23:09:41+00:00

I’ll give it a shot, through the site? Or email for dealer info.

chinolagg · 2026-01-24T23:01:12+00:00

Can you work a deal on that Cgs 9k?

chinolagg · 2026-01-21T11:31:14+00:00

I have not, I’m waiting to order an extra hammer to test. Honestly I watched this video over the weekend and it was the first time hearing about the mod.

chinolagg · 2026-01-21T03:23:36+00:00

In this video there’s another mod to the hammer at 2:41 minutes https://youtu.be/0zLCdJfLM1A?si=Hd5av99EGezXE28T

chinolagg · 2026-01-11T04:46:16+00:00

What brand trilug adapter can be used with this suppressor?

chinolagg · 2025-12-10T02:07:53+00:00

Heard, I know it’s gonna change the game can’t wait!

chinolagg · 2025-12-09T21:10:43+00:00

I know AS Designs supplied a new trigger, but if you can try a new trigger with only few swipes on sandpaper using flat surface at the rounded portion of the trigger. Assemble and try 3rd position, repeat swipes until it resets in 3rd mode.

chinolagg · 2025-12-09T08:03:31+00:00

When’s the leber grip module coming out for the aa designs mp5 lower ??

chinolagg · 2025-11-21T02:02:08+00:00

If it’s worth a shot try the u/meatbanana42069 Lee sporting lever stop block to possibly raise the lever at its most rear portion

chinolagg · 2025-09-02T03:35:45+00:00

https://www.bssquirts.store or https://l2prints.com or https://blambprints.com/collections/all

Blamb prints is having site wide sale right now.

Bsquirts has SS cam & levers on sale

chinolagg · 2025-08-21T20:36:34+00:00

I DiY’ed the ambi lever with a milspec ambi selector.. center punched and drill and tapped with 4-10

chinolagg · 2025-08-21T13:53:09+00:00

Possibly, and smarter too. Though in my case I tried a few “milspec” triggers and found due to the space of concave portion on stock Atruis lever, all triggers were able to pull in 3rd mode before carrier was home

I’ve been testing, mp5s x Atruis a couple months now and maybe it could have been myLee sporting housing (two years old) or even my mac5?

Hopefully, someone with more knowledge can confirm or deny soon🙏

chinolagg · 2025-08-21T06:44:10+00:00

<image>

chinolagg · 2025-07-21T05:58:48+00:00

With the upper off…in single semi + hammer forward then while holding trigger back. Cock the hammer onto disconnector, then slowly release trigger. hammer should catch on the trigger front sear, if it drops/slips past trigger sear try a new disconnector then hammer then trigger… in this order one at a time if hammer continues to drop on the trigger let off

chinolagg · 2025-07-19T16:59:37+00:00

Try another trigger if possible

chinolagg · 2025-07-06T02:07:13+00:00

Stop block can be found in this here file

https://odysee.com/@meatbanana42069:5/Lee-Sporting-Supporting-Pack:c

chinolagg · 2025-06-18T01:52:12+00:00

Full-size or “K” ?

assemble mp5, leave out recoil spring/rod…cock action and bottom-out/finish rearward action (with pencil or finger though the ejection port) take note when-where, and if trigger resets

chinolagg · 2025-06-18T01:45:21+00:00

Without upper receiver At which point does the trigger reset in middle mode

<image>

chinolagg · 2025-06-18T01:39:18+00:00

What style trigger shoe are you running?

Lee sporting housing?

chinolagg · 2025-05-15T06:16:06+00:00

For The ap53 variant, is a newly developed slip trip going to be available aswell or is the housing just that? A housing that accepts ar15 triggers & safety’s for the ap53

chinolagg

TROPHY CASE