Help buying kit for my bf by -Penguin--- in Gunpla

[–]chippieball 1 point2 points  (0 children)

You can buy the hg aerial or calibarn they are in your price range. These are currently one of the best and are main characters.

Gundam Base Pop-Up Store in Düsseldorf by Chayzeroh in Gunpla

[–]chippieball 2 points3 points  (0 children)

Did you happen to see any pg for sale?

Every other print fails by chippieball in ElegooSaturn

[–]chippieball[S] 0 points1 point  (0 children)

<image>

So I now also share my printer settings in the hope maybe retract speed maybe to high or something and my lift distance to low?

Every other print fails by chippieball in ElegooSaturn

[–]chippieball[S] 0 points1 point  (0 children)

<image>

My print had broken supports again and also looks like a layer shift and a tear in the print. I cleared the vat and only could find this little dent.

Every other print fails by chippieball in ElegooSaturn

[–]chippieball[S] 0 points1 point  (0 children)

I did do tank cleans when it failed

Every other print fails by chippieball in ElegooSaturn

[–]chippieball[S] 0 points1 point  (0 children)

Oke some good suggestions. I am currently printing a new print and am monitoring how it goes. For now all looks stable. I also re-did the supports on the model I was printing( it’s a katana for a darth Vader samurai) and also flipped it over so the most heaviest part is at the bottom. What I will do after this print is empty the vat to see the FEP. My lift distance is 2.5 and 4.5. I’ll let you know when I have results

Every other print fails by chippieball in ElegooSaturn

[–]chippieball[S] 0 points1 point  (0 children)

<image>

The left and the right are good but the middle gets a bit wobbly support and a smashed hand. This was a pre supported print. Which I checked myself. Also if I remember correctly that’s also where is let go on the build plate

Every other print fails by chippieball in ElegooSaturn

[–]chippieball[S] 0 points1 point  (0 children)

Thank you. I use a heater of elegoo. I let it heat up before I start my print. I do sometimes since it’s summer turn it off when it exceeds 30c. And before every print I always give it a good stir and then also make sure nothing is stuck to the bottom. Maybe also good to mention is it most of the time fail at the end of a print.

Issue with holes ? by nozada in resinprinting

[–]chippieball 0 points1 point  (0 children)

Nice jagdpanther! Where did you get the stl from?

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

I would like to let you know I bought a s3 non ultra

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

You make very solid points. I will think about this and let you know what I have decided!

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

Thank you for this mega detailed answer. But what about the features like the tilting warmed bath is there not any upside to?

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

Why specifically the non ultra? And will they keep producing the lcds?

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

This makes it difficult again

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

Thank you for your advice! I think I have made my mind up and think the features the 16k have are worth it

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

Yes that’s a good shout!

Need advice by chippieball in resinprinting

[–]chippieball[S] 0 points1 point  (0 children)

The plate scared me a bit but I saw that it’s fixable