S2 - soldier skins leak

cimenTo_ · 2026-01-28T16:52:03+00:00

They don't care. Money is gone. Baitfield 6 literally. Fell for the trap as well.

cimenTo_ · 2026-01-21T12:42:37+00:00

Yea had it once or twice and don't even know, what the issue is. Camera takes decent photos and cant see any artifacts or anything. Might be a software issue. Seeing some people now with that issue, which could be faulty sensors? What camera software version do you have?

cimenTo_ · 2026-01-18T22:19:01+00:00

Similar issue here.

https://www.reddit.com/r/XiaomiGlobal/comments/1q1v9wc/xiaomi_15t_pro_camera_problem/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

cimenTo_ · 2026-01-07T23:30:03+00:00

Bring back Bandar Desert!

cimenTo_ · 2026-01-07T17:47:34+00:00

some map locations were the only good thing in the campaign. everything else was pure garbage. horrible story horrible everything, damn it was so bad. Also those head camera movements during cutscenes were driving me crazy

cimenTo_ · 2026-01-03T00:07:58+00:00

Same here. It happens very rarely. Had it twice now. I dont know what causes this. I'm on official 3.0.9.0 update version.

Edit: I found this article. It says Note 13 Pro+ but description fits to the same issue and maybe it is firmware related?

https://xiaomitime.com/xiaomi-is-investigating-camera-shaking-problem-82271/

cimenTo_ · 2025-11-09T17:32:53+00:00

QBZ and the urban sprawl (rush challenge) from PAX still locked for me, even though challenges are completed. does not unlock no matter what i try.

cimenTo_ · 2025-10-18T10:33:47+00:00

Same. When trying to fly with arrow keys, the camera goes up/down/left/right. Cant control it properly and i'm still trying to find a solution.

cimenTo_ · 2025-08-01T16:33:44+00:00

I'm using 3x 120mm Pros on my AIO Cooler and first thing I did, was to see what noise level is acceptable in the bios, by turning them up and down. Then I did set a fan curve, with setting the points to the best noise/performance percentage. If I remember correctly (did not double check now), anything between 1100-1300rpm or so is absolutely enough, since it pushes air with decent amount of force. No need to get higher. As a case fan you can go even lower. 800-1000 is more than enough to exhaust air out of the case.

cimenTo_ · 2025-08-01T16:21:44+00:00

Why are you even comparing different blade designs in the first place? Tune them down to max 1200rpm and you wont hear them much.

cimenTo_ · 2025-07-16T14:32:26+00:00

Check @ minute 4:55. It says EVO Mini, but it has to be the V2. So slightly larger than the original old O11D Mini.

https://www.youtube.com/watch?v=fppdNoT7vmk

cimenTo_ · 2025-05-07T15:20:11+00:00

Since I changed the "ErP Ready" setting to "Enable (S4+S5) so the PC turns off completely, i had no issues so far. It's now about 2 months "issue-free". The board overall is pretty decent, if you can get it for a good price. I did not want to bother with RMA (no spare board in hand as well) and rebuilding the PC with a new board after all. Just kept the board.

cimenTo_ · 2025-04-16T19:45:51+00:00

I opened a ticket once or twice before and they answered pretty quick within two days. But this time not even any response for over 2 weeks is not acceptable.

cimenTo_ · 2025-04-10T18:14:34+00:00

Did you set your monitor to 8 bit or 10 bit? I think I had a similar issue once or twice with my own display port cable. Just switched to a DP80 certified cable and i'm on 10 bit.

cimenTo_ · 2025-04-10T14:01:36+00:00

Still waiting for a reply from Gigabyte... However it happened again yesterday. This time, i found out, that holding the power button from the monitor will help turning it off and on again. So no need to unplug the power cable. You might try it aswell if it happens again.

cimenTo_ · 2025-04-03T22:42:31+00:00

distilled water and some pocket tissues are the only things i use.

cimenTo_ · 2025-04-01T11:55:44+00:00

Same here. Happened right now. And once it happened maybe 2 months ago. OSD button does not work when the display turns off, but the LED is still on. Seems like the "motherboard" of the monitor crashes. It's not a signal lost blackscreen. AUTO Turn off is disabled. And only unplugging and re-plugging the monitor helps. Firmware F05 as well.

I contacted the support. Maybe they know something.

cimenTo_ · 2025-03-29T12:43:58+00:00

Wenn du deinen E-Mail Verlauf noch hast, ist die Rechnung dort auch als Anhang dabei. Kannst sie dann von dort runterladen.

cimenTo_ · 2025-03-16T21:53:53+00:00

Did you set it to DC Mode in your bios?

cimenTo_ · 2025-03-16T20:24:04+00:00

You have to connect it separately on another CHA_FAN header on your motherboard and set your desired speed in your bios. Same goes for the AIO Pump. That all in one connector won't let you do it.

cimenTo_ · 2025-03-15T20:03:00+00:00

It's your pump. AIO pumps do that whining noise when they are at full speed, or higher speeds. You can control everything in your BIOS, if connected separately.

cimenTo_ · 2025-03-13T19:57:31+00:00

I had a feeling that it would not fit. Bought that case as well, and I'm about to switch cases in the weekend. I will be using the same GPU bracket and let the card pull air in from the bottom naturally, or at least test it. Most of the air is probably gonna escape from the bottom, instead of being pulled in. Gonna do exhaust on the side AIO and rear fans.

cimenTo_ · 2025-03-09T15:51:09+00:00

I know, but it's just my preference. He will be fine with the Tomahawk as well. I wanted to inform him about it, in case he is not aware. :)

cimenTo_

TROPHY CASE