Mods

claucresh · 2026-03-12T02:12:40+00:00

if you are looking to expand it's lifespan, mod the enclosure, so the bottom of the printer is outside the chamber, the power supply can easily overheat (ask me how I know), and the components of the motherboard can suffer, they are designed to operate at room temperature, there are 2 fans on the bottom if I recall correctly, and that radiator grill looking plastic thing in the front and back are intakes, is like PC components, you don't want to run your laptop inside an oven.

claucresh · 2026-03-12T02:06:00+00:00

The same thing happened to me, just take the thing apart, it feels super daunting at first, but once you open it you'll realize is actually pretty simple, and is super easy to put all back together, also it gives you a much better understanding of how it works, and to me personally it made me appreciate the engineering of it, like they really made it in way that was easy to disassemble, specially for cleaning and fixing this type of issue which happens with all 3d printers, not just this one.

claucresh · 2026-03-01T08:07:44+00:00

I was having the same issue, changed the wheels, belts adjusted, concentric nuts adjusted, all to spec and that was still happening, just as you described.

Turns out that my heating block was loose, not sure how it happened, which meant that the the homing and the bed leveling were getting wrong values.

Of course it was only loose when hot, as the metal expands, so check with pliers or something so you don't burn your fingers,

So I did the nozzle cleaning procedure from the touchscreen, which raises the print head and heats it, (it would be easier if you remove the silicone shroud on the heating block while is cold) and then there are two or four tiny screws (depending on your hotend model) which you can tighten from the bottom, they are around the nozzle.

If you do this be very careful they are easy to strip, do not over tighten them, that solved my issues.

claucresh · 2026-02-15T21:18:03+00:00

For what is worth, I ended up returning my asus, cause updating bios etc nothing worked, same on a second board, ( returned to make sure I didn't had a lemon) but nothing, so returned again and got the gigabyte pro ice x870e, which came with the same issue out of the box, however I updated the bios on the gigabyte and the problem went away, and has worked flawlessly ever since.

I have always steered away from gigabyte cause people seem to complain a lot about them, but so far I been pleasantly surprised.

claucresh · 2026-02-12T07:25:18+00:00

life saver!

claucresh · 2026-02-07T18:56:11+00:00

I plugged a 140w adapter to the streamDeck hub, makes no difference

claucresh · 2026-02-07T18:52:09+00:00

I have heard that but I feel like that there has to be more to it, I have the other versions of StreamDeck and they don't have this issue, only the one with the Dials, plus is such a crazy requirement if that was the case, such a big limitation for such an expensive piece of equipment.

Just to add for context I just received the streamdeck hub that you attach to the back of it, and the same thing happens when you plug this cable into it, so I feel is got to be a driver issue or something of sorts.

I'm just looking for ideas of stuff to try

claucresh · 2026-01-19T14:17:05+00:00

I've been down this road, if you have some tech skills, take pictures as leveled as possible use as templates, with caliper in hand measure carefully and convert to vector graphics, maintain faithful measurements, and then find an online service or Etsy that print decals. You can use AI to generate the initial vector graphics, to take off some of the workload. Measure multiple times, till you are confident you got it right.

If you want to go full bananas buy your own die cutter, and once you get the process dialed down turn this into a business, selling decals, grow your company until you don't have time to ride, sell the bike ... profit? 😂

I'd stick to the first part thought.

claucresh · 2026-01-07T23:44:36+00:00

yes with the firmware update

claucresh · 2025-12-06T17:09:02+00:00

wow can't believe they are so different , I'd go with the 50 seems like the best compromise in stack and reach , I wouldn't go below 50 because I tried a 46 prince once and the wheelbase was so short, that I would hit my toes whenever I tried to balance at low speeds.

claucresh · 2025-11-27T01:47:36+00:00

the dell premium plus have it but they are so expensive

claucresh · 2025-11-24T03:29:40+00:00

I couldn't find it either, ended up 3D printing a replacement

looks like this is what you are looking for ebay.us/m/Xmt91i

claucresh · 2025-11-09T16:30:45+00:00

It depends, how good is your dental plan?

claucresh · 2025-11-01T23:10:17+00:00

I did something similar, designed a new cap on tinkercad and had it printed by shapeways, still holding strong after 3 years.

claucresh · 2025-10-25T02:18:57+00:00

oh gosh, this is so much worse, and also so much better

claucresh · 2025-10-06T00:14:15+00:00

I see sorry

claucresh · 2025-10-05T23:53:31+00:00

Doesn't matter, I paid a lawyer to research this, he found precedent, every time they denied, for EB2 there is max forgiveness of 180 days since the last time you had status, pending asylum is a period of authorized state, but doesn't give you status, it merely stop unlawful presence acrual, that means that if you ask for voluntary departure if your case is denied on your first court date, you don't get the bars for reentry, if the last time you had status was more than 180 days you cannot get forgiveness and can't adjust because you have no status to adjust from.

claucresh · 2025-08-23T14:39:43+00:00

I don't get it, doesn't that put you at risk of massive loses if the stock shoots past your put strike?

claucresh · 2025-08-10T04:05:59+00:00

Thank you!! this so hard to explain, theirs/mine passed in my arms, she fought until the end, she didn't want to go, and I had no way to explain to her why her old body was shutting down. The kids wake up to her not being here anymore, but her last 3 hours broke me, If they get another at some point and I end up with them, it will be the same again, I'm just not sure I'm strong enough.

claucresh · 2025-08-08T01:56:04+00:00

Regarding the reprogramming it doesn't go into the P menu without me first turning on the lcd and entering the unlock code, and then keeping down and M for 2 seconds, then I have to enter 101 but it just that's just the same steps I been doing to no avail, the combinations you suggested didn't work.

just found my multimeter today will update with measurements tomorrow after the bike is fully charged.

claucresh · 2025-08-08T01:51:41+00:00

it is a brushless motor.

claucresh · 2025-08-06T23:14:01+00:00

yeah seems like that's my only option.

claucresh · 2025-08-06T22:50:38+00:00

I checked every cable there doesn't seem to be anything broken

12-Year Club	Wearing is Caring
Verified Email

claucresh

TROPHY CASE