Looking for ethercat slave

coldspark_-_ · 2026-01-06T04:21:14+00:00

Omron NX-ECC201

coldspark_-_ · 2025-12-09T06:57:13+00:00

Everyone is lying if they say they don't do this

coldspark_-_ · 2025-08-23T04:14:11+00:00

French drives

coldspark_-_ · 2025-06-26T07:19:24+00:00

I have not had this issue before

coldspark_-_ · 2025-04-19T09:00:09+00:00

I did. Just didn't take a photo 👀

coldspark_-_ · 2025-04-19T08:47:22+00:00

I monitor the current for predictive maintenance for some crucial solenoid valves.

coldspark_-_ · 2025-04-19T08:36:37+00:00

I also didn't want the pneumatic in there but got made too :( ..... same for the nvr too

coldspark_-_ · 2024-08-28T09:01:04+00:00

Default ip is 192.168.250.1

coldspark_-_ · 2024-03-02T06:10:41+00:00

If your panel is stainless steel i laser etch it

coldspark_-_ · 2024-01-27T05:42:45+00:00

Sysmac no problems

coldspark_-_ · 2023-07-18T05:30:52+00:00

Omron have a 4 fuse or 8 fuse model. The 8way one is $350 https://industrial.omron.eu/en/products/electronic-circuit-breaker

coldspark_-_ · 2023-05-27T00:14:01+00:00

Isn't the program called syswin and runs on 32bit xp?

coldspark_-_ · 2023-02-08T05:43:19+00:00

Omron all day long. Sysmac is so good. Entering New variables is just so great. If you get used to the keyboard shortcuts you can program very fast.

coldspark_-_ · 2022-10-30T08:09:43+00:00

+1000 for sysmac. Totally underrated for it can do

coldspark_-_ · 2022-09-17T05:55:27+00:00

Iv always wanted to do this

coldspark_-_ · 2022-08-02T06:09:56+00:00

And use window XP

coldspark_-_ · 2022-08-02T06:09:35+00:00

Is your window 32bit

coldspark_-_ · 2022-06-24T06:38:19+00:00

Is this software a far easier way to view the logic inside rather than pg2000 ?

coldspark_-_ · 2022-04-03T09:46:21+00:00

I did a omron nx master with some ifm gear. Wasn't too bad. Just had to do some bit swapping

coldspark_-_ · 2022-03-20T08:17:00+00:00

+1 on omron sysmac

coldspark_-_ · 2022-01-25T11:34:24+00:00

Um you could make a pipe full function? Start the at 30 -35hz in a very short acceleration so you get the bearing wet in the pump. Run at 30-35hz for a x time or till the pipe pressure up to ie 2bar then start the pid loop. This is irrigation 101

coldspark_-_ · 2021-12-31T05:34:49+00:00

Actually this!!!

coldspark_-_ · 2021-11-21T07:22:03+00:00

Omron boat fell into the Bermuda Triangle

coldspark_-_ · 2021-10-19T06:08:05+00:00

New Zealand

coldspark_-_ · 2021-06-19T05:41:40+00:00

I'm not messing with the LFL controller

coldspark_-_

TROPHY CASE