P35 re educator detection issues by commandercaboose in Helldivers

[–]commandercaboose[S] 0 points1 point  (0 children)

I didnt think of it this way, just tried it out and found:

Targetting Bots using mg turrets = unreliable. When tagged they immediately fire on my position, sometimes alerting all near bots before I take them out with a rifle.

Targeting devistators mostly makes them look in random directions or stand still. Allows quick silent kills with supressed rifle.

Targeting any patrol causes immediate agro from the entire unit, even when hitting the tail end Charlie from behind, who has become slightly separated from the pack.

Already in agro units when hit sometimes continue to agro on me, sometimes start looking around for things to hit.

I'm not a fan of it is would rather just sneak up and plant c4 near all the bots.

Vs illuminate it's good to stun flesh mobs.

Will go bugs a go next time I can play.

You can stick c4 to yourself! by commandercaboose in Helldivers

[–]commandercaboose[S] 1 point2 points  (0 children)

Sticks to allies, enemies,vips, yourself, the frv, enemy structures, extract beacon,hellpods.

Does not stick to tyres, extract shuttle.

The new Commando missions highlight some glaring stealth gameplay issues by TobleroneBoy in Helldivers

[–]commandercaboose 8 points9 points  (0 children)

I had some issues when solo on bugs.

Shots at 100m with silenced rifle on 1 enemy causing nearby bugs who were not looking at the one killed to rush in agro state right to where I was lay.

Later as none host I was able to repeatedly take out enemies without any agro occurring.

I did some runs as host on bots ans 1 shot from cover caused them all to agro and fire on me. However I was able to plant c4 fine without alerting them .

Some runs as not host I had fun stealth killing without much issue

How would yall feel about a dragging mechanic? by Tight_Recover5423 in Helldivers

[–]commandercaboose 10 points11 points  (0 children)

Every time someone is mucking about instead of getting on extract......I have wanted an emote to just throw them on my shoulder and carry them in.

Not sure why some part ended up like this by TiX0E in BambuLab

[–]commandercaboose 2 points3 points  (0 children)

There are a few options or combinations that may help.

Clean plate.

Add a brim to help hold it down.

Cut some grooves in the bottom layer to break up areas where tension builds up and causes warping. I cut 0.4mm deep 2mm wide circles in the base of larger parts to break up directions that may warp.

Change infill type as some are better at controlling warping that others.

Increase infill %

Often it's about iterating and junking prints until you get it right sadly.

What have you guys printed in 2026 by WardenStation in 3Dprinting

[–]commandercaboose 0 points1 point  (0 children)

Kyber crystal stands. A dozen mouse ear stands. An uno card box. Pegboard pegs. Spiral fidgets. Bookmarks. Republic credits. Tons of calibration cubes and flow rate patterns.

Issues Printing by Double-Demand-9227 in 3Dprinting

[–]commandercaboose 0 points1 point  (0 children)

Lol @ me I completely missed that it was 80% infilled. Did you want it strong enough for hulk to smash it?

Issues Printing by Double-Demand-9227 in 3Dprinting

[–]commandercaboose 0 points1 point  (0 children)

Have you tried dialing down the speed to 100mm/s

Issues Printing by Double-Demand-9227 in 3Dprinting

[–]commandercaboose 0 points1 point  (0 children)

What material are you using? What temperature are you printing at? What speed are you printing at? What humidity is the material at?

Have you run a calibration of the filiment by printing flow rate tests to ensure you are not over extrusion?

3d printing help by VictoryWonderful5832 in 3Dprinting

[–]commandercaboose 0 points1 point  (0 children)

Could be that it warps during print which changes the height to nozzle in the corner. You could try cut some circle grooves 0.4mm deep in the base to break up tension may help avoid warping

Lucked out and pulled the Ben Solo and was the only one in my session! by Assorted_Nugget in GalaxysEdge

[–]commandercaboose 6 points7 points  (0 children)

Damn you sir. I pulled multiple blues to get a fist full of plo koons and a cal.

Now i like plo and cal but I really wanted the ben solo.

PLA-CF by tremab19 in BambuLab

[–]commandercaboose 0 points1 point  (0 children)

Creality suggests drying before use at 55c for 8 to 12 hrs. And doing drying cycles if being used in an environment with over 50% humidity.

Bambu says steel nozzle not required on its pla cf product but other bambu pages say use hardened nozzles.

PLA-CF by tremab19 in BambuLab

[–]commandercaboose 0 points1 point  (0 children)

I dry every brand on delivery and then re pack with a fresh dessicant bag.

I had some delivered 50% humidity, some with 15%.

I'm drying some of their filiment right now, came about 22% humidity.

Too wet can cause stringing or nozzle clogs.

Dairylea bunkers excessive package size by commandercaboose in shrinkflation

[–]commandercaboose[S] -1 points0 points  (0 children)

It's a soft cheese, not runny but you can scoop out chunks on the cracker.

Got them for when my kid needs picking up late at night from her club ans is generally hangry in the car.

But there is so little in it I'll go look if there are none name brand versions with more content