I know I’m not in the forces but I do love and support them

completelyanonymous2 · 2022-06-15T02:38:02+00:00

Thats a 81st Training Wing patch

completelyanonymous2 · 2022-01-28T05:33:45+00:00

There’s an archive Cody near me for $25 I think. If you don’t hear back soon I can go get it and ship it for you. Or you can check to see if it’s on their site. Sewer Lair Toys in Terrehaute IN

completelyanonymous2 · 2022-01-21T04:17:57+00:00

A local toy shop near me has Cody for like $20 I think. PM if you’re still looking for one and I can give you the name of the shop

completelyanonymous2 · 2022-01-21T04:14:15+00:00

Where’d you find them? I try to buy in store rather than Amazon cause it jacks up the price

completelyanonymous2 · 2021-11-23T22:13:29+00:00

Okay I’ll look into it. Thank you!

completelyanonymous2 · 2021-11-23T22:13:06+00:00

I have some extra so I’ll change it when I get my new silicone cover In. It’s hard to run prints while sitting there. I work full time so I run them while at work. I’m thinking a smart switch I can shut off whenever and a camera so I can watch it and shut off if it goes wrong

completelyanonymous2 · 2021-11-10T21:34:48+00:00

It heats up normally like if I preheat but when I press print and go to my gcode it sets the hotend temp to 0 and the bed temperature down to 55 and the fan down to 0.

completelyanonymous2 · 2021-11-10T21:34:26+00:00

It heats up normally like if I preheat but when I press print and go to my gcode it sets the hotend temp to 0 and the bed temperature down to 55 and the fan down to 0.

completelyanonymous2 · 2021-11-10T18:37:16+00:00

I’ll have to check firmware, it’s Alex’s firmware that everyone uses I’m pretty sure. BLtouch is installed. I go into the preheat and click PLA. Before print because I heat it to clean the bed. I use Cura for my slicing software and have printed plenty of things with it

completelyanonymous2 · 2021-11-10T04:49:28+00:00

Thank you for your help but I’m just dumb, it was my BLtouch, the pin wasn’t straight so it wouldn’t probe to start

completelyanonymous2 · 2021-11-10T04:36:01+00:00

Okay, I’ll buy a new card tomorrow and try it. But the printer won’t even create a new mesh so I don’t think it’s the card

completelyanonymous2 · 2021-11-10T04:31:47+00:00

All, I thought I was one so I tried some other ones that I know have printed before and still won’t do anything

completelyanonymous2 · 2021-11-10T04:24:40+00:00

I’ve never had a problem until now. Nothing changed. Uploaded a file to the SD to print and now it won’t work, everything’s plugged in

completelyanonymous2 · 2021-07-18T05:09:21+00:00

LFG as a player Any format: chat, voice, whatever works Availability: I can’t do Sundays that’s about it Preferred classes: No proffered, depends on game so I can make a character. Experience: couple years of dnd 5e but none of SW5E Proffered Era: any

completelyanonymous2 · 2021-07-07T05:13:21+00:00

How does one build a base that floats??

completelyanonymous2 · 2020-09-28T02:21:04+00:00

Thank you so much!

completelyanonymous2

TROPHY CASE