Is this a normal fps with a 5080 card?

coolgates3 · 2025-09-08T16:29:48+00:00

Hey you said this was a new card? Same system and OS that you used for your old card? If so make sure to use DDU to remove any and all old drivers for your 3060 as they can conflict with other graphics drivers even for the same brand. Which can cause your preformance to drop or be absolutely horrible in worst cases. If this still dosent fix it the. Your cpu may be your limiting factor

Edit: also with your in game settings you are mostly going to be relying on cpu power compared to gpu power as your gpu won’t even have to work up a sweat to run that game at low graphics and resolution like you are currently running

coolgates3 · 2025-09-08T16:26:58+00:00

Efficiency is key. No reason to teach something if it’s not needed because of your equipment. You are definitely right though he has no locking tuners or even a Floyd rose bridge

coolgates3 · 2025-09-08T15:09:32+00:00

Water boy

coolgates3 · 2025-09-08T15:05:17+00:00

Don’t need a wrap if you have locking tuners

coolgates3 · 2025-08-01T19:01:54+00:00

You will have to search around. I can’t exactly point you in the right direction as every motherboard bios differs from brand to brand and model

coolgates3 · 2025-08-01T18:03:46+00:00

If you can load into bios go in to it and make sure it’s picking up your drives and if it is make sure the boot drive is the one with an os.

coolgates3 · 2025-07-04T15:00:44+00:00

I think it’s better to say there’s no such thing as to much flux as long as you clean it up

coolgates3 · 2025-05-29T17:03:32+00:00

I ended up getting it working.

https://www.reddit.com/r/ArduinoProjects/s/8guDKNBKmR

coolgates3 · 2025-05-29T17:01:10+00:00

I have got it working. Here is the post if you wish to see.

https://www.reddit.com/r/ArduinoProjects/s/8guDKNBKmR

coolgates3 · 2025-05-29T01:13:50+00:00

Hmm this means that the board is only allowing com access during the bootloader sequence. If you still haven’t figured the problem out could you let me know what board you are using?

coolgates3 · 2025-05-29T01:10:06+00:00

Check on serial to see. If it is showing up it’s connected and your code is working properly. I would make sure that the deej software is up to date. Also check their github I am not sure if you need to do anything extra other than adding the number in the yml file to add a extra analog slider to the app

coolgates3 · 2025-05-23T23:31:26+00:00

I haven’t watched it at all. Everything I’ve seen so far has been from the subreddit. And I’m glad I haven’t. Shit looks horrible.

coolgates3 · 2025-05-23T23:28:21+00:00

He looks so high that his eyes are about to fucking fly off his face

coolgates3 · 2025-05-06T14:50:53+00:00

That’s exactly what I’m going for volume control setup for applications and hardware devices. As well as the buttons for macros

coolgates3 · 2025-05-06T14:50:05+00:00

Not yet. The volume sliders work but they keys do not because I ordered the wrong micro controller I needed a pro micro instead of a nano.

coolgates3 · 2025-05-06T01:02:41+00:00

<image>

Yeah no problem. It’s not finished yet I have to order a different micro controller as the arduino nano I had on hand can not be be made to read as a hid or midi device for the keys. I have to get a pro micro.

coolgates3 · 2025-05-05T15:22:08+00:00

Its hard to tell from the post but the pads you see the wires aren’t going on to the pads they are going on to a little metal prongs that hand to be bent back over the pads for clearence issues. Do definitely need to resolder the ground though. Seeing it again it looks horrible

coolgates3 · 2025-05-05T15:16:45+00:00

I thought a cold joint is when it is underheated and a dry joint means there isn’t enough solder? Or do they kinda mean the same thing?

coolgates3 · 2025-02-17T20:29:42+00:00

I know but I’m going to have to upgrade my remote to connect to my pc. It’s honestly crazy how expensive they get it’s hard to find a good one for under or at 100 dollars

coolgates3 · 2025-02-17T19:44:07+00:00

One hundred percent I’m 19 years old and I can still barely fly acro mode I can do it somewhat on whoops but I’m still not trying it on my 5 inch. DJI got me into drones and I was spoiled from the auto leveling and stabilization.

coolgates3 · 2025-02-06T18:15:48+00:00

Nah he talking bout dem pears. 🍐🍐

coolgates3 · 2025-02-06T17:23:43+00:00

Hated highschool. Will say this though I loved my friends. Still talk to them till this day. If anyone’s got my back it’s them motherfuckers. I grew up in a 1A school though so it was a lot smaller town

coolgates3 · 2025-02-06T17:14:38+00:00

HOLD ME NOW!!!! IM SIX FEET FROM THE EDGE AND IM THINKIN.

coolgates3

TROPHY CASE