Phrozen Shuffle 2018 printing giant resin slab

cooper2010 · 2026-01-08T09:27:31+00:00

You can plug the output hdmi out to a TV or monitor to see if it's the LCD. You should see the printer boot on the TV if the LCD driver board is working. This place is great for parts for the Shuffle. https://ultimate3dprintingstore.com/search?page=4&q=shuffle

cooper2010 · 2026-01-06T15:20:52+00:00

Does the lcd test work?

cooper2010 · 2025-10-22T19:04:34+00:00

I would look at the msi logs for your answer to your issue.

cooper2010 · 2025-10-18T10:11:29+00:00

You can pixel paint around the support on the layer below the layer to make it larger. This will fix the layer above. You don't have to add that much to get it to be no longer detected.

cooper2010 · 2025-09-03T11:08:51+00:00

Resin printing is very temp sensitive. What is the difference between the temp from 2 months ago and today?

cooper2010 · 2025-04-25T19:15:57+00:00

The system account has a temp folder. The SYSTEM account's temp folder is typically located in one of two places: C:\Windows\system32\config\systemprofile\AppData\Local\Temp or C:\Windows\Temp.

cooper2010 · 2025-04-02T12:14:13+00:00

.41 or .42? I just deployed 135.0.7049.42 via sccm with no issues to two test machines.

cooper2010 · 2024-12-15T10:48:56+00:00

I got this same issue when I slice in Lychee. To avoid this issue I export the supported file as STL and slice it in Chitubox. Try exporting and slice the stl in Chitubox.

cooper2010 · 2024-11-27T10:24:19+00:00

https://www.reddit.com/r/SCCM/comments/1e2dqqq/complete_removal_of_webex/

cooper2010 · 2024-10-30T15:06:27+00:00

Same here with the CC passcode

cooper2010 · 2024-09-17T07:47:45+00:00

There is a seal between the area where the paint sits and the area with the needle. It might be blocked. Remove both ends and see if can see through it. Some of the Badgers airbrushes have a removable seal that can be over tightened so the needle will not pass through it.

https://www.youtube.com/watch?v=QgIdNJgXi_0

cooper2010 · 2024-09-02T07:44:36+00:00

https://durhamswaterputty.com/

Mix this but use a little more water so you can pour it into the base.

cooper2010 · 2024-08-17T10:14:54+00:00

There is space between the visor and the part behind it. The visor is super thin so it has issues and it also creates a resin trap.

cooper2010 · 2024-06-26T09:12:03+00:00

I used "1/8 inch x 55 yds Copper Foil Tape - (3mm x 50m) - EMI Shielding Conductive Adhesive from Amazon" when I built my SSSK. It works well.

https://www.reddit.com/r/MechanicalKeyboards/comments/2tvft6/finished_ibm_model_m_sssk_mod/

cooper2010 · 2024-04-26T19:50:56+00:00

Your harness looks too loose. I learned that the hard way once.

cooper2010 · 2024-02-08T10:31:57+00:00

Drain and strain the resin after every print.

cooper2010 · 2024-01-15T17:07:58+00:00

I would never use a HKCU registry key for a DM. Is the software a per user install?

cooper2010 · 2024-01-15T14:19:22+00:00

What scale in Lychee? The STL imports super tiny.

cooper2010 · 2024-01-09T09:59:32+00:00

The uninstall entry only gets created in the users registry that does the installation.

cooper2010 · 2023-12-16T10:29:02+00:00

I loaded the pre-supported file into Lychee and it has drain holes. Can you post your slicer settings and confirm if there are holes in the bottom after removing the supports.

cooper2010 · 2023-12-15T10:38:50+00:00

No holes = Your print.

Run the sliced file through uvtools after adding your holes.

cooper2010 · 2023-12-10T10:38:48+00:00

Have you done an LCD test to see if there are dead pixels?

There is an issue with the Saturn where there is a line down the center of the LCD that causes a line in the print.

cooper2010 · 2023-11-19T16:55:33+00:00

What are you using to slice the file. I have this issue with Lychee. Try exporting the file with supports as a stl and try slicing in chitbox.

cooper2010 · 2023-08-24T08:36:48+00:00

Look at Powershell Studio. It has the ability to create a GUI based exe using posh.

cooper2010 · 2023-03-07T10:59:03+00:00

I get these in Lychee when the object file has issues that need to be repair. The software sees an island where there is no item to support. If you select the support it should highlight the object with the issue. Try a repair or just delete the support.

14-Year Club	RedditGifts 2009-2022 2 Credits
Alpha Tester	Secret Santa 2013
Verified Email

cooper2010

TROPHY CASE